Results 101 to 110 of about 67,372 (213)
MetalMat, Volume 3, Issue 1, March 2026.This study experimentally evaluates the performance of eco‐friendly vegetable‐based cutting fluids—coconut, sunflower, and palm oils—during turning of AISI 304 stainless steel under minimum quantity lubrication. Palm oil exhibited superior lubrication and cooling characteristics, yielding the lowest cutting force, temperature, and surface roughness ...
Ranjith Ravindran Nair +3 more
wiley +1 more source
steel research international, Volume 97, Issue 3, Page 1369-1383, March 2026.The processability of the E11018‐G by laser powder directed energy deposition (LP‐DED) is investigated. The effects of powder moisture, ambient humidity, and laser remelting on LP‐DED parts’ porosity are shown. A strong influence of the atomizing gas is observed.
Josu López‐López +7 more
wiley +1 more source
Modifikasi Kekerasan Baja Tahan Karat AISI 316L Dengan Menggunakan Proses Steel Ball Peening [PDF]
, 2020 Baja tahan karat AISI 316L merupan baja tahan karat yang tidak dapat ditingkatkan sifat mekanisnya dengan menggunakan heat treatment. Salah satu metode yang dapat digunakan yaitu dengan mechanical treatment yang salah satunya yaitu steel ball peening ...
Dwi Widodo, Teguh +3 more
core
Acta PolytechnicaThis study carefully compares the effect of microstructure and hardness on the cavitation wear resistance of PPTA (Powder Plasma Transferred Arc) deposited coatings. Deposits were made on a substrate of S235JR structural steel.
Weronika Henzler +5 more
doaj +1 more source
Metals, 2020 Recording the temperature distribution of the layer under construction during laser powder bed fusion (L-PBF) is of utmost interest for a deep process understanding as well as for quality assurance and in situ monitoring means.
Gunther Mohr +4 more
doaj +1 more source
Effect of Temperature and Impurities on the AISI 316L/Microplasma arc welded AISI 316L Galvanic Pair in H3PO4 under Flowing Conditions [PDF]
, 2012 [EN] This work studies the influence of temperature (25, 40 and 60 degrees C) on the corrosion behavior of base and welded AISI 316L stainless steels in phosphoric acid polluted by sulfuric acid and chloride ions under hydrodynamic conditions (Reynolds ...
Guenbour, Abdellah +3 more
core +1 more source
Aisi 316l-aisi 2205 farkli paslanmaz çelik çiftinin kaynak kabiliyeti [PDF]
, 2017 Bu çalışmada endüstride gıda, eczacılık, kimya, petrokimya ve gemicilik alanlarında sıklıkla kullanılan östenitik ile dubleks paslanmaz çelik çiftinin birleştirilmesinde kaynak yönteminin ve ilave metal seçiminin birleştirme mekanik özelliklerine ve ...
Manısalı, Berkay +3 more
core
Metallurgical and Mechanical Research on Dissimilar Electron Beam Welding of AISI 316L and AISI 4340
Advances in Materials Science and Engineering, 2016 Dissimilar electron beam welding of 316L austenitic stainless steel and AISI 4340 low alloy high strength steel has been studied. Studies are focused on effect of beam current on weld geometry, optical and scanning electron microscopy, X-ray diffraction ...
A. R. Sufizadeh, S. A. A. Akbari Mousavi
doaj +1 more source
Efek Tekanan Shot peening Terhadap Kekasaran Permukaan dan Kekerasan AISI 316L Stainless steel [PDF]
, 2015 Penelitian ini dilakukan untuk mengetahui Efek tskanan shot peening terhadap kekasaran permukaan dan kekerasan AISI 316L Rekayasa fisik material yang digunakan untuk megubah sifat mekanik pada AISI 316L stainless steel salah satunya shot peening.
Rizky, EnggalR
core
Characterization of borided AISI 316L stainless steel implant [PDF]
, 2002 The present study reports on characterization of borided AISI 316L stainless steel implant. Boronizing heat treatment was performed on a cylindrical bar of AISI 316L austenitic surgical stainless steel with a diameter of 2mm and a length of 10 mm using ...
Özbek, İbrahim, Bindal, Cuma
core