A portable load cell for in-situ ore impact breakage testing [PDF]
, 2002 This paper discusses the design and characterisation of a short, and hence portable impact load cell for in-situ quantification of ore breakage properties under impact loading conditions.
Banini, George, Bourgeois, Florent
core +1 more source
Corrosion fatigue of high strength fastener materials in seawater [PDF]
Environmental effects which significantly reduce the fatigue life of metals are discussed. Corrosion fatigue is a major concern in the engineering application of high strength fasteners in marine environments.
Tipton, D. G.
core +1 more source
Frictional and structural characterization of ion-nitrided low and high chromium steels [PDF]
Low Cr steels AISI 41410, AISI 4340, and high Cr austenitic stainless steels AISI 304, AISI 316 were ion nitrided in a dc glow discharge plasma consisting of a 75 percent H2 - 25 percent N2 mixture.
Spalvins, T.
core +1 more source
Effect of Cavitation on The Corrosion Behavior of Ti(CN)/TiNb(CN) Multilayer in Seawater
International Journal of Electrochemical Science, 2014 The superficial wear generated by cavitation in an electrolyte as sodium chloride 3.5%, causes damage in steels AISI 4140 by corrosion, it is commonly used in hydraulic machines, therefore suggest to coat with a Ti(CN)/TiNb(CN) multilayer system ...
W. Aperador, E. Delgado, C. Amaya
doaj +1 more source
Pengaruh Proses Hardening pada Baja Hq 7 Aisi 4140 dengan Media Oli dan Air terhadap Sifat Mekanis dan Struktur Mikro [PDF]
, 2013 Proses hardening dilakukan pada temperatur pemanasan 850oC terhadap baja AISI 4140 dengan memberikan holding time selama 1 jam serta 2 macam media pendingin yaitu oli dan air. Selanjutnya dilakukan proses tempering pada temperatur 600oC dengan pemberikan
Sutowo, C. (Cahya), Susilo, B. A. (Bayu)
core +1 more source
Reciprocal dry sliding wear behaviour of B4Cp reinforced aluminium alloy matrix composites [PDF]
, 2012 Manuscript DraftIn the present work, AlSi9Cu3Mg alloy matrix composites reinforced with 15 and 19% (vol.) B4Cp were produced by squeeze casting route at 850 °C under low vacuum.
Kerti, Isil +2 more
core +1 more source
Corrosion Resistanne of the [TiN/CrN]n Coatings Deposited on Steel AISI 4140
International Journal of Electrochemical Science, 2013 In this paper is presented the improvement against corrosion of the multilayer coatings [TiN/CrN]n with periods of 20, 50, 100 and 200 bilayers deposited by the PVD magnetron sputtering technique on carbon steel AISI 4140.
W. Aperador, A. Delgado, J. Duque
doaj +1 more source
Welding of stell ABNT4140 without posterior thermal treatment.
Revista Tecnologia, 2009 The procedure for conventional welding of the AISI 4140 steel, due to the martensite formation in the heated affected zone (HAZ), contemplates a postwelding heat treatment (PWHT) to relief the stress and to improve the toughness of this zone.
Jesualdo Pereira Farias +1 more
doaj
International Journal of Electrochemical Science, 2014 This article presents the evaluation of the corrosion erosion resistance erosion caused by cavitation generated on the binary type coatings [TiN / CrN]200, ternary [TiN / AlTiN]200 and quaternary [TiCN / TiNbCN]200 obtained by physical vapour deposition ...
W. Aperador, E. Ruíz, A. Mejia
doaj +1 more source
Electrochemical Corrosion of Hot Pressing Titanium Coated Steels for Biomaterial Applications
International Journal of Electrochemical Science, 2010 Titanium diffusion process was applied to three selected steels, namely series AISI 1045, 4140 and stainless steel 304 using the hot pressing technique for a possible biomaterial use.
F. Barragán +4 more
doaj +1 more source