Results 91 to 100 of about 1,266 (172)
Prediction of surface roughness in hard milling of AISI D2 tool steel [PDF]
, 2007 This paper presents a study of the development of a surface roughness model in end milling of hardened steel AISI D2 using PVD TiAIN coated carbide cutting tool. The hardness of AISI D2 tool lies within the range of 56-58 HRe. The independent variables
Hafiz, A.M. Khalid +3 more
core
Cutting Tool Edge Temperature in Dry Hard Orthogonal Cutting AISI D2 Tool Steel with CBN Tool
, 2010 The influence of cutting conditions on temperature of CBN cutting tool edge during dry hard machining of hardened AISI D2 tool steel (62±1HRC) is investigated in this paper.
Wen Cui Luo +3 more
core +1 more source
Niobium Boride Layers Deposition on The Surface AISI D2 Steel by a Duplex Treatment
, 2015 In this paper, we investigated the possibility of deposition of niobium boride layers on the surface of AISI D2 steel by a duplex treatment. At the first step of duplex treatment, boronizing was performed on AISI D2 steel samples at 1000 degrees C for 2h
PAZARLIOĞLU, SÜLEYMAN SERDAR
core +1 more source
, 2015 In drilling, temperature is an important factor for the tool and the machining performance. For this reason, analysis of the temperature in the cutting zone is essential for predicting the machining performance.
Tekaüt, I., Demir, H.
core
, 2017 Hard dry machining of AISI T1 and AISI D2 steels at comparable hardness (around 59 HRC) were performed at 50 m/min, 80 m/min and 100 m/min cutting speeds separately with uncoated alumina ceramic tool inserts (Al2O3 + TiC), in order to study the effect ...
Julia Dosbaeva +5 more
core +1 more source
Regression Modeling of EDM Process for AISI D2 Tool Steel with RSM
Journal of Engineering, 2018 In this paper, Response Surface Method (RSM) is utilized to carry out an investigation of the impact of input parameters: electrode type (E.T.) [Gr, Cu and CuW], pulse duration of current (Ip), pulse duration on time (Ton), and pulse duration off time ...
Shakir M. Mousa
doaj +2 more sources
Minería y Geología, 2015 Se realizó un análisis de la calidad superficial y la vida de la herramienta durante el mecanizado con altas velocidades de los aceros endurecidos AISI D2 y AISI D6, en dos regímenes de lubricación.
Maritza Mariño-Cala +1 more
doaj
Journal of Alloys and Metallurgical SystemsThis study aims to observe the residual stress in a substrate and predict stress behavior during the laser deposition process (DED) using finite element analysis (FEA). The residual stress observed on the substrate surface indicated that stress variation
Su Seong Woo +3 more
doaj +1 more source
Surface Integrity in Micromilling of Hardened AISI D2 Tool Steel
, 2015 This paper presents workpiece surface integrity of micromilling hardened tool steel AISI D2. These include 3D mapping of surface texture, analysis of microstructure and microhardness variation.
Mohamad Nor, Norhafiez +4 more
core +1 more source
Duplex coatings on AISI H13 and AISI D2 tool steels by using plasma nitriding and TiN-PVD.
, 2003 No presente trabalho foi avaliado o efeito da microestrutura e da capacidade de suportar carregamento de camadas nitretadas produzidas em aços ferramenta AISI H13 e AISI D2 sobre a aderência e a resistência ao desgaste microabrasivo de revestimentos de ...
Franco Júnior, Adonias Ribeiro +1 more
core +1 more source