Results 141 to 150 of about 545 (179)

Experimental Study in HSM of Hardened Steel AISI D2

Advanced Materials Research, 2009
Hardened steel is widely used for good mechanical property, but its machinability is bad comparatively. It is efficient to enhance metal removed rate when high speed milling (HSM) hardened steel, but tool wear is rapid. In this paper, high-speed milling experiments were carried out for hardened steel with TiAlN coated tools.
B.Y. Qi, Ning He, Liang Li
openaire   +1 more source

Influence of Cutting Edge Radius in Micromachining AISI D2

Applied Mechanics and Materials, 2013
Chip formation is a dynamic process that is often non linear in nature. A chip may not form when the depth of cut is less than a minimum chip thickness. This paper presents an investigation of cutting edge radius effect on micromachining AISI D2 tool steel via simulation.
J.B. Saedon, A. Hakim A. Halim, H. Husain, M.S. Meon, Muhamad Fauzi Othman   +4 more
openaire   +1 more source

Tribocorrosion behavior of surface-modified AISI D2 steel

Surface and Coatings Technology, 2020
Abstract Three different thermochemical coatings were obtained on the surface of an AISI D2 cold work tool steel under different process conditions through the use of boriding, titanizing, and borotitanizing (titanizing followed by boriding) treatments.
openaire   +1 more source

Micro-Milling of Hardened AISI D2 Tool Steel

Advanced Materials Research, 2012
The paper presents an experimental investigation into the slotting of hardened AISI D2 (~62HRC) tool steel using 0.5mm diameter coated (TiAlN) tungsten carbide (WC) end mills. SEM analysis of tool morphology and coating integrity was undertaken on all tools prior to testing.
J.B. Saedon, S.L. Soo, D.K. Aspinwall, A. Barnacle   +3 more
openaire   +1 more source

Prediction of Boride Thickness on Tool Steels AISI D2 and AISI H13 Using Boriding Kinetics

Advanced Materials Research, 2014
Cold and hot work tool steels AISI D2 and AISI H13, respectively, were borided using a packed boriding process. Boriding temperature range of 1123 1223 K was performed with different boriding time up to 6 hr, afterwards, near-surface properties of the borided tool steels AISI D2 and H13 were characterized.
Yossapong Boonplook, Patiphan Juijerm
openaire   +1 more source

Weldability and Joining Characteristics of AISI D2/AISI 304 Steels Using Semisolid Diffusion Joining

Solid State Phenomena, 2019
The application of hybrid structures or components made of dissimilar metal offers the potential to utilize the advantages of different materials often providing unique solutions to engineering requirements. However, the joining of materials by conventional welding techniques becomes difficult if the physical properties such as melting temperature and ...
Mohammed N. Abdul Razaq, M. Zaidi Omar, Salah Al-Zubaidi, Khaled S. Alhawari, Mnel A. Abdelgnei   +4 more
openaire   +1 more source

The characteristics of cutting forces in the micro-milling of AISI D2 steel

Journal of Mechanical Science and Technology, 2009
The interaction effect of parameters to surface topography and cutting forces is investigated, and the magnitudes of these parameters are determined in the micro-milling of AISI D2 steel. The results show that the feed per tooth has a prominent impact on the surface topography.
Cheng-Zhe Jin, Ik-Soo Kang, Jin-Hyo Park, Su-Hoon Jang, Jeong-Suk Kim   +4 more
openaire   +1 more source

Influence of varied cryotreatment on the wear behavior of AISI D2 steel

Wear, 2009
Abstract Exploration of the benefit of cryotreatment for achieving improvement in wear resistance of die/tool steel is a topic of current research interest. A series of wear tests has been carried out on AISI D2 steel samples subjected to cryotreatment at 77 K for different durations.
D. Das, A.K. Dutta, K.K. Ray
openaire   +1 more source

Surface Integrity in Hot Machining of AISI D2 Hardened Steel

Advanced Materials Research, 2012
This study presents experimental results of machined surface integrity of die material (AISI D2 hardened steel) when hot machining (induction heating) assisted end milling using coated carbide is applied. The aim of this work was to study the influence of induction heating temperature, cutting speed, and feed on the effects induced by hard milling on ...
Mohd Amri Lajis, A.K.M. Nurul Amin, A.N. Mustafizul Karim   +2 more
openaire   +1 more source

A comprehensive review on cold work of AISI D2 tool steel

Metallurgical Research & Technology, 2017
As a common material in mould and die application, AISI D2 cold work tool steel has proven to be a promising chosen material in the industries. However, challenges remain in using AISI D2 through a modified version with a considerable progress having been made in recent years.
Mohd Aidil Shah bin Abdul Rahim, Mohamad bin Minhat, Nur Izan Syahriah Binti Hussein, Mohd Shukor bin Salleh   +3 more
openaire   +1 more source