Results 61 to 70 of about 141,194 (208)

Corrosion Behavior of TiN Coated AISI D2 Steel [PDF]

open access: yes, 2014
Bu çalışmada, nitrürlenmiş AISI D2 soğuk iş takım çeliği yüzeyinde kutu difüzyon tekniği ile oluşturulan titanyum nitrür (TiN) kaplama tabakasının korozyon davranışı incelenmiştir.
Çeğil, Özkan, Şen, Şaduman
core   +1 more source

AISI D2 Soğuk İş Takım Çeliğine Uygulanan Endüstriyel Kriyojenik İşlemin Aşınma Davranışları Üzerindeki Etkisi

open access: yes, 2018
In this study, industrial cryogenic process after conventional heat treatment process for various holding time was applied to AISI D2 (DIN 1.2379) cold work tool steel. The effects of the industrial cryogenic process on the wear behavior was investigated.
Enes Ersöz   +3 more
core   +2 more sources

Growth kinetics and wear resistance of vanadium carbide on AISI D2 steel produced by TRD process

open access: yesMaterials Research Express, 2021
Vanadium carbide coating was obtained on the surface of AISI D2 steel by thermal reactive diffusion process using molten borax as based salt and vanadium pentoxide as vanadium donor. The process was performed at 900 °C, 940 °C, 980 °C and 1020 °C for 3 h,
Lianpu Zhou   +3 more
doaj   +1 more source

Probing Early Particle‐Cell Membrane Interactions via Single‐Cell and Single‐Particle Interaction Analysis

open access: yesAdvanced Functional Materials, Volume 35, Issue 46, November 12, 2025.
The pre‐internalization phase of endocytosis remains poorly characterized at single‐cell levels. Single‐cell pre‐internalization mechanics are investigated using advanced robotic techniques. Cancer cells exhibit biphasic adhesion – rapid initial binding followed by reinforcement – while fibroblasts show gradual engagement.
Houari Bettahar   +6 more
wiley   +1 more source

Enhancing wear resistance of tool steel materials for industrial automobile component using cryogenic treatment

open access: yesScientific Reports
The durability of sheet metal punching tools depends largely on their wear resistance and frictional behaviour during service. Deep cryogenic treatment (DCT) has emerged as an effective post-heat-treatment process for improving the tribological ...
Kiran S. Phad   +3 more
doaj   +1 more source

High-Strength D2 tool steel via material extrusion additive manufacturing and post-heat treatment

open access: yesMaterials & Design
AISI D2 tool steel was fabricated using metal-materials extrusion additive manufacturing (M−MEX), followed by heat treatment to optimize its microstructure and mechanical properties. These were compared with conventional wrought D2 materials.
Min-Su Jeon   +5 more
doaj   +1 more source

Effect of Post-Heat Treatment on the AISI M4 Layer Deposited by Directed Energy Deposition

open access: yesMetals, 2020
Currently, high-speed steel (HSS) powders are deposited locally on a metal surface through direct energy deposition (DED) onto hardface tool steel. Although the HSS powder enhances the hardness and the abrasion resistance of a metal surface, it makes the
Gyeong Yun Baek   +3 more
doaj   +1 more source

EuPdSn2: magnetic structures in view of resonant X‐ray Bragg diffraction

open access: yesActa Crystallographica Section B, Volume 81, Issue 5, Page 440-444, October 2025.
Structure factors informed by magnetic symmetry for resonant X‐ray diffraction by EuPdSn2 using Eu atomic resonances E1–E1 and E1–E2. Axial and polar (Dirac) electronic Eu multipoles are compulsory.The magnetic properties of materials hosting Eu2+ (J = 7/2, 4f7) ions have attracted much attention in the science of strongly correlated electrons. In part
Stephen W. Lovesey
wiley   +1 more source

Maquinabilidade dos aços AISI H13 e D2 [PDF]

open access: yes, 2016
Mestrado em Engenharia MecânicaNo presente trabalho foi realizado um estudo baseado na maquinabilidade, através do acabamento superficial e da precisão dimensional, dos aços AISI H13 e D2, utilizando ferramentas cerâmicas de geometria convencional e ...
Vilaça, Marco João Ferreira
core  

Home - About - Disclaimer - Privacy