Results 11 to 20 of about 1,120,503 (214)

Characterization and Diffusion Kinetics of Silicon on AISI D2 Steel [PDF]

open access: yesSilicon, 2023
This paper presents the simultaneous influence of two different activators (NH4Cl and NaF) on the kinetic evolution during siliconising of steel. The AISI D2 tool steel surface was coated by pack siliconising through the growing of silicon on the surface. Pack siliconising was accomplished by employing a mixture of powders of Si 12 wt% + NH4Cl 0.5 wt% +
Najafizadeh, Mojtaba   +5 more
openaire   +3 more sources

Mechanical Properties and Microstructure Characterization of AISI “D2” and “O1” Cold Work Tool Steels

open access: yesMetals, 2019
This research analyzes the mechanical properties and fracture behavior of two cold work tool steels: AISI “D2” and “O1”. Tool steels are an economical and efficient solution for manufacturers due to their superior mechanical ...
Mohammed Algarni
doaj   +2 more sources

Pack Siliconizing Optimization of AISI D2 Tool Steel

open access: yesSilicon, 2022
AbstractThe paper describes the pack siliconizing optimization procedure for AISI D2 tool steel. Pack siliconizing was performed by employing different treating temperatures (falling in the range 650–950 °C) and times (falling in the range 2–4 h). The siliconizing atmosphere was obtained through silicon (at 12 wt.%) with the addition of different ...
Mojtaba Najafizadeh   +4 more
openaire   +2 more sources

MITIGATION OF AGRICULTURAL ENERGY REQUIREMENT IN BANGLADESH USING MICROALGAE PRODUCTION [PDF]

open access: yesJournal of Mechanical Engineering and Sciences, 2013
A high quality joint between tool steel and stainless steel alloys is hard to achieve with the conventional welding process. In this study, a new process of joining semi-solid AISI D2 tool steel and AISI 304 stainless steel using a partial remelting ...
Mohammad Farzid Hasan   +3 more
doaj   +1 more source

Desirability response surface for wear resistance of ball-end milled surface of AISI D2 steel under dry cutting condition.

open access: yes, 2023
Desirability response surface for wear resistance of ball-end milled surface of AISI D2 steel under dry cutting condition.
Guosong Zhang (3210132)   +3 more
core   +1 more source

Effect of Post-Heat Treatment on the AISI M4 Layer Deposited by Directed Energy Deposition

open access: yesMetals, 2020
Currently, high-speed steel (HSS) powders are deposited locally on a metal surface through direct energy deposition (DED) onto hardface tool steel. Although the HSS powder enhances the hardness and the abrasion resistance of a metal surface, it makes the
Gyeong Yun Baek   +3 more
doaj   +1 more source

Investigation of Cutting Performance of Nano/Layered Hard Coatings in Face Milling of AISI D2 Steel

open access: yesDüzce Üniversitesi Bilim ve Teknoloji Dergisi, 2023
In the die-molding industry, milling steels in a hardened condition is common. Tool wear and cutting-forces occurring during this process must be considered for better surface quality.
Bilal Kurşuncu
doaj   +1 more source

Mechanical properties and kinetics of boride layers on AISI D2 steel produced by plasma paste boriding [PDF]

open access: yes, 2021
In the present study, the AISI D2 steel has been treated by the plasma paste boriding process using a gas mixture of 70% H2-30% Ar with 70% of borax and 30% SiC. The boriding treatment has been carried out at 700, 750 and 800 °C for an exposure time of 3
Makuch, Natalia ; Poznan University of Technology, Institute of Materials Science and Engineering, Pl. M Sklodowskiej-Curie 5, 60-965 Poznan, Poland   +3 more
core   +1 more source

Study of Short Times Tempering for AISI D2 Cold Work Tool Steel

open access: yesMaterials Research, 2023
Short time tempering has been applied to steels to improve toughness keeping the hardness at the same level. For AISI D2 tool steel, typical thermal cycles are quench and temper.
Maycoln D. Conci   +3 more
doaj   +1 more source

Laser transformation hardening effect on hardening zone features and surface hardness of tool steel AISI D2

open access: yesMechanics and Advanced Technologies, 2017
The relationship of technological input regimes of the laser transformation hardening on change the hardening depth, hardening width, and hardening angle, as well as surface hardness of the tool steel AISI D2 using multifactor experiment with elements of
D. Lesyk   +5 more
doaj   +1 more source

Home - About - Disclaimer - Privacy