Results 31 to 40 of about 1,120,503 (214)

Effect of uniaxial load on microstructure and mechanical properties of Thixo-joint AISI D2 tool steel

open access: yesJournal of Mechanical Engineering and Sciences, 2019
Tool steels are commonly used to cut metal materials due to their distinctive hardness, resistance to abrasion and deformation. However, tool steels are difficult to be joined using conventional fusion welding process.
F. Adnan, Z. Sajuri, M. Z. Omar
doaj   +1 more source

Growth kinetics and wear resistance of vanadium carbide on AISI D2 steel produced by TRD process

open access: yesMaterials Research Express, 2021
Vanadium carbide coating was obtained on the surface of AISI D2 steel by thermal reactive diffusion process using molten borax as based salt and vanadium pentoxide as vanadium donor. The process was performed at 900 °C, 940 °C, 980 °C and 1020 °C for 3 h,
Lianpu Zhou   +3 more
doaj   +1 more source

Characterization chip formation of commercial steel materials at low speed cylindrical grinding processes

open access: yesMATEC Web of Conferences, 2018
Cylindrical grinding is the process of metal removal using multiple cutting point. The objective of the study is to investigate the chip characteristics (shape and width) and surface roughness materials. The materials are AISI 1020, AISI 1045, AISI 1090,
Isti Nugroho Wahyu   +2 more
doaj   +1 more source

Laser Micro Polishing of Tool Steel 1.2379 (AISI D2): Influence of Intensity Distribution, Laser Beam Size, and Fluence on Surface Roughness and Area Rate

open access: yesMetals, 2021
Within the scope of this study, basic research was carried out on laser micro polishing of the tool steel 1.2379 (AISI D2) using a square, top-hat shaped intensity distribution. The influence of three different quadratic laser beam sizes (100 µm, 200 µm,
André Temmler   +4 more
doaj   +1 more source

Segregation and carbide evolution in AISI D2 tool steel produced by curved continuous casting

open access: yesJournal of Materials Research and Technology, 2023
A promising process with the concept of ‘green, efficient and economic’ was carried out to produce a typical AISI D2 tool steel through curved continuous casting (C3).
Tinghui Man   +7 more
doaj   +1 more source

Growth Mechanism and Kinetics of Siliconizing of AISI D2 Tool Steel

open access: yesSilicon, 2022
AbstractThe present paper goes into details of the kinetics of silicide layer growth on AISI D2 during surface siliconizing. Pack cementation was employed in order to siliconize the steel surface. Siliconizing was conducted by using powder mixtures Si 12 wt.% + NH4Cl 0.5 wt.% + Al2O3at 923, 1073 and 1223 K for 2 to 6 h, respectively.
Mojtaba Najafizadeh   +5 more
openaire   +1 more source

Ultrasonic Vibration Assisted Laser Processing: A Hybrid Paradigm for Extreme Surface Enhancement

open access: yesRare Metals, Volume 45, Issue 10, October 2026.
ABSTRACT Traditional laser processing techniques offer many advantages, but they often encounter limitations such as heat‐affected zones, recast layers, residual tensile stresses, and poor surface finish. The integration of ultrasonic vibration (UV) presents a promising hybrid approach to overcome these challenges by introducing beneficial effects like
Aziz Ul Hassan Mohsan   +6 more
wiley   +1 more source

ANALYSIS OF CUTTING FORCE AND CHIP MORPHOLOGY DURING HARD TURNING OF AISI D2 STEEL [PDF]

open access: yesJournal of Engineering Science and Technology, 2015
In this research work AISI D2 tool steel at a hardness of 55 HRC is being used for experimental investigation. Cutting speed, feed rate and depth of cut are the cutting parameters considered for the experimentation along with tool geometry namely, nose ...
X. M. ANTHONY
doaj  

Improvement in the Hard Milling of AISI D2 Steel under the MQCL Condition Using Emulsion-Dispersed MoS2 Nanosheets

open access: yesLubricants, 2020
The present work shows the process for MoS2 nanosheet production by liquid N2-queched bulk, a novel method having highly efficient, green, and facile operation.
Pham Quang Dong   +5 more
doaj   +1 more source

Analysis of AISI D2 Steel by using SEM Images

open access: yesInternational Journal of Recent Technology and Engineering, 2020
Hard turning is a new emerging technique in manufacturing industry which involves turning of hard steel having hardness more than 60 HRC. Here in the present work, the objective of the study is steel type ENX160CrMo having hardness 62 HRC. Hard turning were carried out at different cutting parameters and chip hardness and micro- chip SEM images were ...
openaire   +1 more source

Home - About - Disclaimer - Privacy