Results 151 to 160 of about 889,141 (311)
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones
Advanced Engineering Materials, EarlyView.A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell +3 more
wiley +1 more source
Electrochemical plating of Sn – Ag alloy applicable as a solder
Журнал Белорусского государственного университета: Химия, 2018 The additions of hydroquinone, 1,4-butandiol and citrate ions to the known strongly acidic sulfate-thiourea solution for electrochemical deposition of Sn – Ag low-melting alloy are proposed, which provide to obtain the alloys of composition near to the ...
Olga N. Vrublevskaya +5 more
doaj
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Cryogenic Properties of a New Tough-Strong Iron Alloy [PDF]
A program was undertaken to develop an iron-base alloy having a fracture toughness of 220 MPa. m superscript 1/2 with a corresponding yield stress of 1.4 GPa (200 ksi) at-196 C. An Fe-12Ni alloy was selected as the base alloy. Factors considered included
Stephens, J. R., Witzke, W. R.
core +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Unraveling the Superior High-Temperature Oxidation Behavior of FeNiCuAl-Based High-Entropy Alloys: Roles of Cr, Co, and Mn Alloying Additions. [PDF]
Materials (Basel)Ren K, Gao X, Yang R, Fu J.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
The effect of yttrium addition on the ratcheting behavior of magnesium. [PDF]
PLoS OneShou H +8 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source