Results 261 to 270 of about 1,452,683 (339)

Effect of Water Aging on the Mechanical Properties of Hybrid Carbon/Aramid Reinforced Thermoplastic Composites

Advanced Engineering Materials, EarlyView.
This study investigates the mechanical properties of Carbon/Aramid intraply hybrid fiber‐reinforced Elium composites under 6 months of water aging. After aging, flexural strength decreases by 25.89%, tensile strength by 4.40%, and fracture toughness by 21.56%.
Muhammed Huseyin Guzel, Gurol Onal
wiley   +1 more source

Enhanced Strength of Al-10Ce-3Mg-5Zn Heat-Resistant Alloy by Combining Extrusion and Heat Treatment. [PDF]

Materials (Basel)
Zhang H, Li Z, Xiao D, Wu M, Huang Y, Liu W.   +5 more
europepmc   +1 more source

Impacts of Device Geometry and Layout on Temperature Profile during Large‐Area Photonic Curing

Advanced Engineering Materials, EarlyView.
The study investigates how gate geometry affects peak curing temperature during photonic curing of solution‐processed indium zinc oxide thin‐film transistors. Using 3D simulations and experimental validation, it reveals that larger gate areas and smaller aspect ratios increase curing temperature and thus improve transistor performance. Findings provide
Yasir Fatha Abed, Neel Chatterjee, Bing Luo, Sarah L. Swisher   +3 more
wiley   +1 more source

Effect of intrinsic heat treatment on the microstructure and mechanical properties of Al-Cu alloy fabricated by wire arc directed energy deposition. [PDF]

Sci Rep
Yang B, Li X, Lei S, Li Y, Jin X, Zhao G, Li X.   +6 more
europepmc   +1 more source

Microstructure, Mechanical Properties, and Antibacterial Performance of Novel Fe‐Mn‐Zn Nanocrystalline Alloys Produced by Mechanical Alloying

Advanced Engineering Materials, EarlyView.
This article presents the development of Fe‐Mn‐Zn nanocrystalline alloys (0–9 wt% Zn) by mechanical alloying and subsequently hot pressing. Their microstructure, density, hardness, wear resistance, corrosion behavior, and antibacterial properties are systematically examined.
Ilker Emin Dag, Funda Kilic, Mrutyunjay Panigrahi, Baris Avar   +3 more
wiley   +1 more source

Determination of Phase Boundaries in Solid Alloy Systems by a Diffusion Technique

, 1951
C. E. Ransley
openalex   +1 more source

Corrosion resistance of multilayer silane sol-gel coatings on titanium Grade 2 and Ti6Al4V alloy. [PDF]

Sci Rep
Kierat O, Dudek A.
europepmc   +1 more source

Coercivity Improvement in Ce‐Containing (Nd,Pr)‐Fe‐B‐Based Sintered Magnets by Application of the 2‐Powder Method

Advanced Engineering Materials, EarlyView.
This study investigates the magnetic properties and microstructures of 2PM‐manufactured Ce‐containing (Nd,Pr)‐Fe‐B magnets. The addition of Nd and Dy significantly enhances coercivity by 25% and 81%, respectively, attributed to core‐shell structures.
Chi‐Chia Lin, Konrad Opelt, Jürgen Dieter Rossa, Fernando Maccari, Songhak Yoon, Jürgen Gassmann, Oliver Gutfleisch   +6 more
wiley   +1 more source

Effect of Chromium on Mechanical Properties and Corrosion Behavior of Copper-Nickel Alloy. [PDF]

Materials (Basel)
Chu H, Yang Z, Cao Y, Zhang W, Xie H, Yuan Y, Wang H, Yue D.   +7 more
europepmc   +1 more source

Fractographic Analysis and Fatigue Behavior of Additively Manufactured Ni‐Superalloy Components with Post Processing Heat Treatment and Hot Isostatic Pressing

Advanced Engineering Materials, EarlyView.
A study of mechanical properties and fractography of PBF‐LB/M‐built Inconel 718, performing heat treatments and hot‐isostatic pressing, is presented. Ultimate tensile strength and fatigue behavior are evaluated, examining differences in maximum load behavior, elongation, and regimes of fatigue.
David Sommer, Ben Truetsch, Cemal Esen, Ralf Hellmann   +3 more
wiley   +1 more source