Results 121 to 130 of about 1,104,683 (311)

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

Advanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan, Jack Keddie, Byoungyoul Park, Hyun‐Joong Chung   +3 more
wiley   +1 more source

Atmospheric Induction Direct Chromium Alloying of Steel Using FeAlSiCa as a Metallothermic Reductant. [PDF]

Materials (Basel)
Akhmetov A, Makhambetov Y, Smagulov A, Sadyk Z, Toleukadyr R, Baisanov S.   +5 more
europepmc   +1 more source

Mechanical alloying and milling

, 2004
C. Suryanarayana, In-Seop An
semanticscholar   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

First-principles study on elastic properties of Cu, (Cu_1- <i>_x</i> ,Ni <i>_x</i> )₃Sn and interfacial mechanical properties of (Cu_1- <i>_x</i> ,Ni <i>_x</i> )₃Sn/Cu in the lead-free solder joint. [PDF]

Beilstein J Nanotechnol
Hua G.
europepmc   +1 more source

Carbon alloys

Carbon, 1995
openaire   +2 more sources

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

A Machine Learning-Guided Search of Cu-Based Bimetallic Alloys That Favor CO Dimerization in CO $_2$ RR. [PDF]

ChemSusChem
Salomone M, Wang W, Raffone F, Re Fiorentin M, Risplendi F, Cicero G.   +5 more
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Enhancing Solid Solution Strengthening of TiZrNb Alloys via W and Cr Alloying: First-Principles Insights into Mechanical Properties. [PDF]

Materials (Basel)
Sun Z, Ma G, Guo Q, Ou R, Guo L, Ji C, Zhang Z, Li L, Wang C, He Y.   +9 more
europepmc   +1 more source