Results 171 to 180 of about 77,060 (305)

The Influence of Alloying Elements on the Hot Corrosion Behavior of Nickel-Based Superalloys. [PDF]

Materials (Basel)
Badea TA, Dombrovschi M.
europepmc   +1 more source

Characteristic effects of alloying elements on β solidifying titanium aluminides: A review. [PDF]

Heliyon, 2020
Raji SA, Popoola API, Pityana SL, Popoola OM.   +3 more
europepmc   +1 more source

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

Advanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan, Jack Keddie, Byoungyoul Park, Hyun‐Joong Chung   +3 more
wiley   +1 more source

Assessment of the cytotoxicity of commercially available titanium alloy with pure grade titanium (CP-Ti) and other alloying elements for dental implants: An <i>in vitro</i> study. [PDF]

Natl J Maxillofac Surg
Nair VS, Sankar K, Kshirsagar R, Sane VD, Nallasivamoorthy A, Singh V.   +5 more
europepmc   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Influence of Alloying Elements on the Phase Structure, Stress-Strain Behavior, and Fracture Toughness of Ni₃Sn: A First-Principles Study. [PDF]

Materials (Basel)
Zhang H, Dai J, Cao Y, Zhang Y, Bao M, Yin Y.   +5 more
europepmc   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Investigation of the Influence of Alloying Elements Ni, Cr, Co and Mo on the Crystallization Process, Phase Composition and Corrosion Resistance of AlSi25Cu4Cr and AlSi25Cu5Cr Alloys. [PDF]

Materials (Basel)
Dochev B, Dimova D, Trojan K, Čapek J, Kamarska K, Chuchulska B.   +5 more
europepmc   +1 more source

Effects of Alloying Elements (C, Mo) on Hydrogen Assisted Cracking Behaviors of A516-65 Steels in Sour Environments. [PDF]

Materials (Basel), 2020
Park JS, Lee JW, Hwang JK, Kim SJ.
europepmc   +1 more source