Results 21 to 30 of about 691,156 (237)

Formation of Ti–Zr–Cu–Ni bulk metallic glasses [PDF]

, 1995
Formation of bulk metallic glass in quaternary Ti–Zr–Cu–Ni alloys by relatively slow cooling from the melt is reported. Thick strips of metallic glass were obtained by the method of metal mold casting.
Johnson, W. L., Lin, X. H.
core   +1 more source

Hot deformation behavior, microstructure evolution and slip system of Mg-2Zn-0.5Mn-0.2Ca alloy

Journal of Materials Research and Technology, 2022
The hot deformation behavior of as-cast Mg-2Zn-0.5Mn-0.2Ca alloys was investigated by hot compression tests conducted at 250–400 °C with strain rates of 0.001–1 s−1.
Deqing Ma, Shuai Yuan, Shiyu Luan, Peipeng Jin, Hengrui Hu, Jinhui Wang, Xiaoqiang Li   +6 more
doaj   +1 more source

Investigation on some factors affecting crack formation in high resistance aluminum alloys [PDF]

, 2017
Aluminum alloys having good mechanical properties are Al-Zn-Mg alloys (7xxx) and Al-Cu-Li alloys (Weldalite®). These alloys may be subjected to stress corrosion cracking.
Brotzu, A., Felli, F., Pilone, D.
core   +3 more sources

Construction of flexible and wearable 3D TiO2 NTs@Ti mesh for physiological detection based on sweat

JCIS Open, 2021
The biosensors with flexibility and breathability turn out to be a vital means of non-intrusive detection of multi-components biochemical markers in human sweat. For this end, three-dimensional (3D) structure TiO2 nanotube arrays were in-situ established
Jianwei Yu, Peng Zhang, Tengyu Chen, Qiuchen Lv, Li Gao, Bingxin Liu, Junyuan Duan, Zhaofeng Wu, Jian Li   +8 more
doaj   +1 more source

Revealing microstructures evolution and dynamic recrystallization mechanisms of Mg–Sn–Mn alloy during compressive deformation at elevated temperature

Results in Materials, 2023
The flow behavior of as-extruded Mg–3Sn-1.5Mn (wt.%) alloy was systematically researched via isothermal compression tests. The compressive temperatures (T) were from 250 °C to 400 °C, the strain rates were from 0.001 s−1 to 1s−1 and the true strain ...
Yunduo Feng, Jinhui Wang, Shiyu Luan, Shuai Yuan, Xiaoyu Liu, Xiaowei Li, Li Han, Qi Wei   +7 more
doaj   +1 more source

The Influence of Alloy Composition and microstructure on the corrosion behaviour of Cu-Ni alloys in seawater [PDF]

, 1983
The aim of the study was to relate the general corrosion behaviour of CuNi 10-alloys in seawater with its iron content and microstructure. To that end the microstructure of four commercial alloys with various Fe-contents (1.20-1.78%) and there laboratory
Baailey, Berg, Efird, Efird, Gilbert, Ijsseling, Ijsseling, Kolster, Kolster, Macdonald, Popplewell, Pourbaix, Stewart, Swartzendruber, Syrett, Syrett, Tracy, Vreeland   +17 more
core   +2 more sources

CsCl-Type Compounds in Binary Alloys of Rare-Earth Metals with Zinc and Copper [PDF]

, 1964
The CsCl-type structure has been previously reported in alloys of copper with yttrium, gadolinium, and erbium, [1] and of zinc with lanthanum, cerium, and praesodymium.
Chao, C. C., Duwez, P., Luo, H. L.
core   +1 more source

Thermal deformation behavior of Mg–3Sn–1Mn alloy based on constitutive relation model and artificial neural network

Journal of Materials Research and Technology, 2023
The flow stress behavior of Mg–3Sn–1Mn alloy during thermal compression deformation was systematically studied. The thermal compression simulation experiment was carried out at different deformation temperatures and different strain rates in the range of
Xiaowei Li, Jinhui Wang, Jiaxuan Ma, Ting Yang, Shuai Yuan, Xiaoyu Liu, Yunduo Feng, Peipeng Jin   +7 more
doaj   +1 more source

Tailoring the microstructure, mechanical properties and damping capacities of Mg–4Li–3Al–0.3Mn alloy via hot extrusion

Journal of Materials Research and Technology, 2022
The microstructure, mechanical properties, and damping performance of Mg–4Li–3Al–0.3Mn alloy were systematically investigated in this research. The results show that the microstructure of Mg–4Li–3Al–0.3Mn alloy is significantly refined after extrusion ...
Gang Zhou, Yan Yang, Li Sun, Jiwei Liu, Hongju Deng, Chen Wen, Guobing Wei, Bin Jiang, Xiaodong Peng, Fusheng Pan   +9 more
doaj   +1 more source

Effect of homogenization heat treatment on refractory phase and grain size of 5083 aluminum alloy

Cailiao gongcheng, 2023
In order to study the changes in the content, type of the refractory phases and grain size during homogenization of the 5083 aluminum alloy, material microstructure was characterized by metallographic microscope (OM), scanning electron microscope(SEM ...
HUANG Yuanchun, WU Zhenli, WANG Xucheng, ZHAO Jianye, MA Shangkun, YAN Jijun   +5 more
doaj   +1 more source