Results 91 to 100 of about 1,088,927 (341)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Low-dose alum application trialled as a management tool for internal nutrient loads in Lake Okaro, New Zealand [PDF]
, 2008 Aluminium sulfate (alum) was applied to Lake Okaro, a eutrophic New Zealand lake with recurrent cyanobacterial blooms, to evaluate its suitability for reducing trophic status and bloom frequency.
Gibbs, Max M. +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Effect of aluminium sheet surface conditions on feasibility and quality of resistance spot welding [PDF]
, 2010 A study investigating the effect of sheet surface condition on resistance spot welding (RSW) of aluminium has been carried out. This concentrates on two automotive aluminium alloys; AA5754 and AA6111, used for structural and closure applications ...
Briskham +14 more
core +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Co-reduction of aluminium and lanthanide ions in molten fluorides : application to cerium and samarium extraction from nuclear waste [PDF]
, 2009 This work concerns the method of co-reduction process with aluminium ions in LiF–CaF2 medium (79–21 mol.%) on tungsten electrode for cerium and samarium extraction.
Chamelot, Pierre +3 more
core +2 more sources
The Aluminyl Anion: A New Generation of Aluminium Nucleophile.
Angewandte Chemie, 2020 Trivalent aluminium compounds are well known for their reactivity as Lewis acids/electrophiles, a feature that is exploited in many pharmaceutical, industrial and laboratory-based reactions. Recently, a series of isolable aluminium(I) anions ('aluminyls')
Jamie Hicks +3 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann +6 more
wiley +1 more source
Neues über die schwedische Diamantsynthese und andere metallkatalysierte polymorphe Umwandlungen
CHIMIA, 1961 Liander und Lundblad haben kürzlich Einzelheiten über die Diamantsynthese der ASEA mitgeteilt, die mit einem hochdrucktechnisch völlig neuartigen Pressentyp durchgeführt wurde.
Hans J. Rodewald
doaj +1 more source
Evaluation of gas metal arc welding with alterating shielding gases for use on AA6082T6 [PDF]
, 2012 Studies have been carried out to determine the effects of implementing alternating shielding gases for 6082T6 aluminium alloy welding. Alternating shielding gases is a newly developed method of supplying shielding gases to the weld area to enhance the ...
Campbell, Stuart +3 more
core +1 more source