Results 31 to 40 of about 529,915 (180)

A super-ductile alloy for the die-casting of aluminium automotive body structural components [PDF]

, 2014
Super-ductile die-cast aluminium alloys are critical to future light-weighting of automotive body structures. This paper introduces a die-cast aluminium alloy that can satisfy the requirements of these applications.
Ji, S, Watson, D, Fan, Z
core   +1 more source

Aluminium - a versatile packaging material

, 2022
S.923-927 : Abb.,Tab.,Lit.Der Artikel gibt einen Überblick über den Werkstoff Aluminium im Verpackungsbereich, beschreibt den derzeitigen Entwicklungsstand und zeigt künftige Trends auf.
Schricker, G.
core   +1 more source

Inspection of Prebaked Carbon Anodes Using Multi-Spectral Acousto-Ultrasonic Excitation

Metals, 2017
Reduction cell operation in primary aluminum production is strongly influenced by the properties of baked anodes. Producing consistent anode quality is more challenging nowadays due to the increasing variability of raw materials. Taking timely corrective
Moez Ben Boubaker, Donald Picard, Carl Duchesne, Jayson Tessier, Houshang Alamdari, Mario Fafard   +5 more
doaj   +1 more source

Nanoprocessing of Industrial Rejects for Controlling Operational Energy of Buildings

Advances in Civil Engineering, 2022
This study investigates the pozzolanic potential of industrial waste, which fails to meet the chemical composition as defined by the various international standards, e.g., IS: 3812 (Part 1): 2017 and ASTM C618-19 to adopt as a supplementary cementitious ...
Sandeep Tembhurkar, Priyanka Nayar, Naumanuddin Azad, Rahul Ralegaonkar, Mangesh Madurwar   +4 more
doaj   +1 more source

Performances of Green and Eco-Friendly Ramming Pastes in EGA Pots

Metals, 2016
Consistent and high quality ramming paste products, installed according to optimized procedures, are required for improved operation and longer pot life. However, ramming paste used to be a hazardous product and needs special precautions for handling and
Bénédicte Allard, Mohamed Tawfik, Arvind Kumar   +2 more
doaj   +1 more source

Crack Detection Method Applied to 3D Computed Tomography Images of Baked Carbon Anodes

Metals, 2016
Carbon anodes used in the aluminium industry were imaged through destructive and non-destructive testing (NDT) methods. For the latter case, computed tomography (CT), which has previously been used to map the 3D apparent density distribution, was ...
Donald Picard, Julien Lauzon-Gauthier, Carl Duchesne, Houshang Alamdari, Mario Fafard, Donald P. Ziegler   +5 more
doaj   +1 more source

Interpolation of Pathway Based Non-Destructive Testing (NDT) Data for Defect Detection and Localization in Pre-Baked Carbon Anodes

Metals, 2022
Producing consistent quality pre-baked carbon anodes for the Hall–Héroult aluminum reduction process is challenging due to the decreasing quality and increasing variability of anode raw materials.
Daniel Rodrigues, Carl Duchesne, Julien Lauzon-Gauthier   +2 more
doaj   +1 more source

A low-cost open-source automated shot peen forming system

HardwareX, 2022
The aerospace industry relies on shot peen forming to form sheet metal parts and correct distortion in machined parts. The shot peen forming community is developing simulation and planning methods to meet the industrial need for automation.
Wassime Siguerdidjane, Farbod Khameneifar, Frédérick P. Gosselin   +2 more
doaj   +1 more source

Cold Rolling Technology Optimization for EN AW 4343/3003/4343 Cladded Aluminum Alloys and Influence of Parameters on Microstructure, Mechanical Properties and Sustainable Recyclability

Metals
The present study investigates the accumulative roll bonding process applied to the EN AW 3003 aluminum alloy, serving as a composite material on both sides and consisting of the EN AW 4343 aluminum alloy.
Bojan Kropf, Peter Cvahte, Matija Arzenšek, Jakob Kraner   +3 more
doaj   +1 more source

Migration Between Two Inverse Time-Overcurrent Curves of Different Standard: Experience at Siguragura Power Station

Jurnal Nasional Teknik Elektro, 2019
The inevitable replacement of electro-mechanical protection relays with more recently-developed microprocessor-based protection relays poses challenges to engineer, one of which is migration from existing manufacturer’s non-standard inverse time ...
Bagus Brahmantya Gautama
doaj   +1 more source