Results 41 to 50 of about 529,915 (180)
Effect of aluminium sheet surface conditions on feasibility and quality of resistance spot welding [PDF]
, 2010 A study investigating the effect of sheet surface condition on resistance spot welding (RSW) of aluminium has been carried out. This concentrates on two automotive aluminium alloys; AA5754 and AA6111, used for structural and closure applications ...
Shergold, Mike +3 more
core +1 more source
The Role of Anode Manufacturing Processes in Net Carbon Consumption
Metals, 2016 Carbon anodes are consumed in electrolysis cells during aluminum production. Carbon consumption in pre-bake anode cells is 400–450 kg C/t Al, considerably higher than the theoretical consumption of 334 kg C/t Al.
Khalil Khaji, Mohammed Al Qassemi
doaj +1 more source
Lubricated sliding wear behaviour of aluminium alloy composites [PDF]
, 2005 Interest in aluminium alloy (Al-alloy) composites as wear resistant materials continues to grow. However, the use of the popular Al-alloy-SiC composite can be limited by the abrasive nature of the SiC, leading to increased counterface wear rates.
Rainforth, W.M., Jones, H., Walker, J.C.
core +1 more source
Study on the impact wear mechanism and damage modes of compacted graphite cast iron
Journal of Materials Research and Technology, 2022 The impact wear mechanism of compacted graphite cast iron (CGI) at different temperatures (room temperature, 300 °C, 400 °C, and 500 °C) and impact frequencies (10 Hz, 12 Hz, and 14 Hz) was analyzed.
Yue Wu +5 more
doaj +1 more source
Empirical Model of Bearing Temperature Saturation at Asahan II Hydro-Turbine-Generator
Jurnal Teknik Mesin, 2018 Bearing temperature saturation is a common phenomenon observed during no-load run and full-load tests of Asahan II hydro-turbine-generators. Despite complex heat transfer mechanism involved behind it, simple model can be constructed to predict bearing ...
Bagus Brahmantya Gautama
doaj +1 more source
Applied Sciences, 2018 In the present paper, the microstructures of three kinds of in-situ reinforcements Al-Ti-C, Al-Ti-B, and Al-Ti-B-C-Ce were deeply investigated using a combination of scanning electron microscopy, X-ray diffraction spectroscopy, and transmission electron ...
Lusha Tian +7 more
doaj +1 more source
Materials Research Express, 2023 The tension-tension fatigue test of the compacted graphite cast iron (CGI) alloy was carried out by RDL100 universal testing at 500 °C and 550 °C, respectively. A tension-tension trapezoidal load is applied to the CGI specimen.
Wu Yue +7 more
doaj +1 more source
Clustering and Precipitation during Early-Stage Artificial Aging of Al–Si–Mg(–Cu) Foundry Alloys
Metals, 2023 High-Si aluminum foundry alloys are an important material class for products with complex 3D geometries where casting is the most suitable production method. With Mg and/or Cu additions, these alloys gain strength upon heat treatment due to the formation
Sigurd Wenner +3 more
doaj +1 more source
Electrochemistry of aluminium in room temperature A1C13-TMPAC molten salts. [PDF]
, 1997 PhDAluminium can be electrodeposited on tungsten, aluminium, platinum, nickel and glassy carbon from 2: 1 A1C13-TMPAC (trimethylphenylammonium chloride) molten salts at room temperature.
Zhao, Yuguang
core +2 more sources
TEM characterisation of near surface deformation resulting from lubricated sliding wear of aluminium alloy and composites [PDF]
, 2007 Aluminium alloy composites have been extensively investigated for use in tribo-contact applications, however little detailed literature exists on the sub-surface microstructural evolution as a result of lubricated sliding wear.
Rainforth, W.M. +7 more
core +1 more source