Results 91 to 100 of about 102,666 (312)

A summary of current advancements in hybrid composites based on aluminium matrix in aerospace applications

Hybrid Advances
As fuel prices rise and environmental rules become more stringent, there is pressure on the aerospace sector to create lighter, more efficient aircraft. Fuel usage is significantly reduced as a result of using lightweight alloys to make the aircraft as a
Abideen Temitayo Oyewo, Oluleke Olugbemiga Oluwole, Olusegun Olufemi Ajide, Temidayo Emmanuel Omoniyi, Murid Hussain   +4 more
doaj   +1 more source

Analytical and Experimental Determination of FML Stiffness and Strength Properties. [PDF]

, 2015
The paper presents application of analytical methods of determining the mechanical properties of Fibre Metal Laminates. Chosen micromechanical methods were employed to predict elastic moduli and strength of FML panels.
Kamocka, Monika, Mania, Radosław J.
core   +1 more source

Permittivity measurement of thermoplastic composites at elevated temperature [PDF]

, 2001
[Abstract]: The material properties of greatest importance in microwave processing of a dielectric are the complex relative permittivity Epsilon = Epsilon' - jEpsilon'', and the loss tangent, tan Delta = Epsilon'/Epsilon''.
Ball, James A. R., Horsfield, Brendan, Ku, Harry S., Siores, Elias   +3 more
core   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

A consolidation process model for film stacking glass/PPS laminates [PDF]

, 2009
The applied pressure, processing temperature and holding time influence the\ud consolidation of thermoplastic laminates. A model to optimise the processing\ud parameters is proposed.
Akkerman, R., Grouve, W.J.B.
core   +5 more sources

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Retracted: Investigation on Inorganic Salts K2TiF6 and KBF4 to Develop Nanoparticles Based TiB2 Reinforcement Aluminium Composites. [PDF]

Bioinorg Chem Appl, 2023
And Applications BC.
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Relationship between Al2O3 Content and Wear Behavior of Al+2% Graphite Matrix Composites

Science and Engineering of Composite Materials, 2020
In this study, the microstructure and wear behaviours of aluminium composites, reinforced with different amounts of (3-12%) Al2O3 and 2% (% vol.) graphite were investigated.
Simsek D., Simsek I., Ozyurek D.
doaj   +1 more source