Results 111 to 120 of about 102,666 (312)

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Microstructure of metal matrix composites reinforced by ceramic microballoons [PDF]

, 2012
Metal matrix composites reinforced by ceramic hollow microspheres were produced as special porous metals, called metal matrix syntactic foams (MMSFs).
Májlinger, Kornél, Orbulov, Imre Norbert   +1 more
core  

Experimental investigation on performance of fabrics for indirect evaporative cooling applications [PDF]

, 2016
© 2016 Indirect evaporative cooling, by using water evaporation to absorb heat to lower the air temperature without adding moisture, is an extremely low energy and environmentally friendly cooling principle.
Fancey, Kevin S., Ma, Xiaoli, Xu, Peng, Zhao, Xudong   +3 more
core   +1 more source

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Assessment of the infrared welding process for a carbon fabric reinforced pps [PDF]

, 2012
This study assesses the use of infrared welding for a carbon fabric reinforced polyphenylene sulphide. Infrared light is used in order to melt the thermoplastic matrix of the two components, after which they are joined together under pressure.
Allaer, Klaas, De Baere, Ives, Degrieck, Joris, Jacques, Stefan, Van Paepegem, Wim   +4 more
core  

Experimental study of sandwich structures as armour against medium-velocity impacts [PDF]

, 2013
An experimental impact study has been conducted on sandwich structures to identify and improve armour solutions for aeronautical applications. The objectives are to find the best configurations, i.e. the non-perforated targets with the minimal weight and
Bouvet, Christophe, Kolopp, Amélie, Rivallant, Samuel   +2 more
core   +3 more sources

Raman Spectroscopic Identification of Oxide Phases in a Corroded MgO–Steel Composite Anode Used in Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler, Serhii Yaroshevskyi, Alexander Adamczyk, Mahnaz Mehdizadehlima, Julia Richter, Cameliu Himcinschi, David Rafaja, Alexandros Charitos, Christos G. Aneziris, Jens Kortus   +9 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

Pyramidal Structures on Yttria‐Stabilized Zirconia after High Temperature Exposure at 1500°C: New Features on an Old Material

Advanced Engineering Materials, EarlyView.
New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold, Dylan Jennings, Robert Vaßen   +2 more
wiley   +1 more source

Wear behaviour of Al-MWCNT composites by varying MWCNTs concentration

Journal of Alloys and Metallurgical Systems
The present study illustrates the mechanical and wear behaviour of Al-MWCNT composites by varying MWCNTs concentration (0 %,0.25 %, 0.50 % & 1 %) by weight in composites. These composites were synthesized through sintering in the muffle furnace after
Rahul Sharma, C. Sasikumar, Jayashree Baral   +2 more
doaj   +1 more source