Results 131 to 140 of about 102,666 (312)

Investigation of the mechanical and tribological properties of scrap Al alloy MMCs reinforced with pumice/B4C particles through the electrodeposition of Ni-P surface coating

Results in Engineering
In this research work, the scrap aluminium metal matrix composites were successfully fabricated through stir casting technique with novel combinations of reinforcements like pumice and B4C.
R. Jeevanantham, Dega Nagaraju
doaj   +1 more source

Properties of Metal Matrix Composite of Aluminium 11.8% Silicon Reinforced with Different Particulates [PDF]

, 2006
A composite material is a materials system composed of a mixture or combination of two or more micro or macro constituents that differ in form and chemical composition and which are essentially insoluble in each other.
Vijayaram, Thoguluva Raghavan
core  

Dielectric Barrier Discharge Plasma Deoxidation of Natively Oxide Layer of Copper Powders in a Fluidized Bed

Advanced Engineering Materials, EarlyView.
This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang, Annett Wollmann, Thomas Gimpel, Alfred P. Weber   +3 more
wiley   +1 more source

Aluminium oxide hydroxyapatite composites

, 2007
Febs ...
Peker, I., Gunduz, O., Oktar, F., Salman, S., Agathopoulos, S., Ozyegin, L.   +5 more
openaire   +1 more source

Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid

Advanced Engineering Materials, EarlyView.
This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar, Jana Hubálková, Steffen Dudczig, Gert Schmidt, Florian Kerber, Thomas Schemmel, Patrick Gehre, Christos G. Aneziris   +7 more
wiley   +1 more source

Deterministic Detection of Single Ion Implantation

Advanced Engineering Materials, EarlyView.
Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead, Lok Kan Wan, Maddison Coke, Janet Jacobs, Nicholas F. L. Collins, Mark C. Rosamond, Richard J. Curry   +6 more
wiley   +1 more source

Investigation on Inorganic Salts K2TiF6 and KBF4 to Develop Nanoparticles Based TiB2 Reinforcement Aluminium Composites.

Bioinorg Chem Appl, 2022
Mohanavel V, Kumar KR, Sathish T, Velmurugan P, Karthick A, Ravichandran M, Alfarraj S, Almoallim HS, Sureshkumar S, JoshuaRamesh Lalvani JI.   +9 more
europepmc   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam

Advanced Engineering Materials, EarlyView.
Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley   +1 more source

Deformability of a textile reinforcement modified with nanofibres [PDF]

, 2010
Deformability of a textile fabric is studied experimentally using a) friction test, b) out-of-plane compression, and c) bending. These tests reveal that a grafting of the fabric with carbon nano-fibres can significantly deteriorate its deformability ...
Akkerman, R., Gorbatikh, L., Koissin, V., Kotanjac, Z., Lomov, S.V., Warnet, L.   +5 more
core   +1 more source