Study of Deep Drawing Combined with Ironing of A7075 Aluminum Alloy [PDF]
MATEC Web of ConferencesThis study focuses on the process analysis and pass design of compound deep drawing with ironing processes of A7075 aluminum alloy. At first, A7075-T6 aluminum alloy workpiece is annealed to enhance the formability.
Hwang Yeong-Maw +2 more
doaj +1 more source
Forgeability of AZ Series Magnesium Alloy produced by Twin Roll Casting [PDF]
, 2017 Plastic forming of magnesium alloy is hardly reported because of its low forgeability. The productions of magnesium alloy are mainly produced by casting. Typical wrought magnesium alloy is AZ31.
Aoki, A. (Atsuhiro) +11 more
core +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Development and characterization of Powder Metallurgy (PM) 2XXX series Al alloy products and Metal Matrix Composite (MMC) 2XXX Al/SiC materials for high temperature aircraft structural applications [PDF]
The results of a series of material studies performed by the Lockheed Aeronautical Systems Company over the time period from 1980 to 1991 are discussed. The technical objective of these evaluations was to develop and characterize advanced aluminum alloy ...
Chellman, D. J. +2 more
core +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Determination of low-temperature fatigue properties of structural metal alloys Final report, Jul. 1964 - Aug. 1965 [PDF]
Fatigue testing and determination of low temperature properties of structural metal alloys - aluminum alloy, stainless steel, and nickel ...
Keys, R. D. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Research status and development trend of mechanical properties of 7 series ultra-high strength aluminum alloy [PDF]
ITM Web of ConferencesAluminum alloy material has the characteristics of good durability, corrosion resistance, light weight, easy processing, maintenance-free, recyclable, etc.
Jiao Yufeng
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Research Progress on the Influence of Microstructure on Stress Corrosion Behavior and Mechanisms of 7000 Series High-Strength Aluminum Alloys [PDF]
Cailiao BaohuThe 7000 series (Al-Zn-Mg-Cu) high-strength aluminum alloy is one of the highest strength aluminum alloy series.Stress corrosion cracking (SCC) is a key factor affecting its service safety and stability.In this paper, the anodic dissolution mechanism and
YANG Yang, LI Songmei, JIA Xuejiao, LIU Jianhua, YU Mei
doaj +1 more source