Results 71 to 80 of about 483,474 (280)

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Process intensification in gas-to-liquid reactions: plasma promoted Fischer-Tropsch synthesis for hydrocarbons at low temperatures and ambient pressure

Green Processing and Synthesis, 2013
The Fischer-Tropsch synthesis (FTS) for the conversion of carbon monoxide and hydrogen to higher hydrocarbons was investigated over a supported Cu/Co catalyst promoted by dielectric-barrier discharges (DBDs) at relatively low temperatures and ambient ...
Al-Harrasi Wail S.S., Zhang Kui, Akay Galip   +2 more
doaj   +1 more source

THERMAL IR IMAGING: IMAGE QUALITY AND ORTHOPHOTO GENERATION [PDF]

The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences, 2018
This paper deals with two aspects of photogrammetric processing of thermal images: image quality and 3D reconstruction quality. The first aspect of the paper relates to the influence of day light on Thermal InfraRed (TIR) images captured by an Unmanned ...
A. Sledz, J. Unger, C. Heipke
doaj   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Numerical investigation of thermal contrast for interfacial debonding detection in concrete-filled steel tubular structures under hydration heat

Results in Engineering
Concrete-filled steel tubular (CFST) structures are extensively used for infrastructures, but the issue of debonding formation during construction remains prevalent. To address and mitigate this problem, this study investigates the temperature variations
Chongsheng Cheng, Xianwang Zeng, Ruili Wang, Haonan Cai, Ri Na, Hong Zhang   +5 more
doaj   +1 more source

Solvent Exfoliation of Electronic-Grade, Two-Dimensional Black Phosphorus

, 2015
Solution dispersions of two-dimensional (2D) black phosphorus (BP), often referred to as phosphorene, are achieved by solvent exfoliation. These pristine, electronic-grade BP dispersions are produced with anhydrous, organic solvents in a sealed tip ...
Chen, Kan-Sheng, Hersam, Mark C., Kang, Joohoon, Lee, Jae-Hyeok, Liu, Xiaolong, Wells, Spencer A., Wood, Joshua D.   +6 more
core   +2 more sources

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Local Rheology Relation with Variable Yield Stress Ratio across Dry, Wet, Dense, and Dilute Granular Flows

, 2019
Dry, wet, dense, and dilute granular flows have been previously considered fundamentally different and thus described by distinct, and in many cases incompatible, rheologies.
de Klerk, David N., Durán, Orencio, Govender, Indresan, Pähtz, Thomas, Trulsson, Martin   +4 more
core   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source