Effect of deposition current density and annealing temperature on the microstructure and magnetic properties of nanostructured Ni-Fe-W-Cu alloys [PDF]
Science of Sintering, 2019 Ni-Fe-W-Cu alloy powders were obtained by electrodeposition from an ammonium citrate bath at current densities ranging between 70 and 600 mA cm-2. As the deposition current density increased, the contents of Fe and W in the alloy increased, and ...
Spasojević Milica +5 more
doaj +1 more source
Characterization of FeCoV alloy processed by PIM/MIM route [PDF]
Science of Sintering, 2017 In this study the characterization of FeCo-2V alloys toroidal samples produced by PIM/MIM technology was presented. The feedstock for metal injection molding (MIM) was prepared by mixing starting FeCoV powder with a low viscosity binder.
Nedeljković Borivoje +4 more
doaj +1 more source
npj Computational Materials, 2023 Numerical simulations have revolutionized material design. However, although simulations excel at mapping an input material to its output property, their direct application to inverse design has traditionally been limited by their high computing cost and
Han Liu +7 more
doaj +1 more source
The thermal and magnetic properties of the Fe89.8Ni1.5Si5.2B3C0.5 and Fe81B13Si14C2 amorphous alloys [PDF]
Science of Sintering, 2015 This paper investigates the thermal and magnetic properties of two iron based amorphous alloys with different Fe-content: Fe89.8Ni1.5Si5.2B3C0.5 and Fe81B13Si14C2.
Kalezić-Glišović A. +2 more
doaj +1 more source
Morphological, microstructural and magnetic characteristics of electrodeposited Ni-Fe-W-Cu alloy powders [PDF]
Science of Sintering, 2020 Nanostructured Ni-Fe-W-Cu alloy powders were electrodeposited from an alkaline ammonium citrate solution on a titanium cathode. Powder particles were dendrite- and cauliflower-shaped.
Spasojević Miroslav +4 more
doaj +1 more source
The Stabilization of Amorphous Zopiclone in an Amorphous Solid Dispersion [PDF]
AAPS PharmSciTech, 2015 Zopiclone is a poorly soluble psychotherapeutic agent. The aim of this study was to prepare and characterize an amorphous form of zopiclone as well as the characterization and performance of a stable amorphous solid dispersion. The amorphous form was prepared by the well-known method of quench-cooling of the melt. The solid dispersion was prepared by a
Milne, Marnus +2 more
openaire +4 more sources
Crystals, 2021 Hybrid materials, i.e., the organically modified silicates (ORMOSIL) based on zincphthalocyanine (ZnPc) and silica glass matrix were synthesized by the sol-gel method using protic solvents (methanol, ethanol, isopropanol, butanol) and aprotic solvent (N ...
Barbara Popanda +2 more
doaj +1 more source
Amorphous Thermal Spray Coating with Hard Materials Exhibiting Cleavage Fracture
Tribology Online, 2015 Hard materials were mixed with alloy powders and thermally sprayed at an ultra rapid cooling rate of more than 106°C/s. For example, 65Ni15Cr16P4B at% alloy powder containing tungsten carbide was thermally sprayed.
Toshiharu Morimoto +3 more
doaj +1 more source
Synthesis, structure and properties of nickel-iron-tungsten alloy electrodeposits - Part II: Effect of microstructure on hardness, electrical and magnetic properties [PDF]
Science of Sintering, 2016 Nanostructured nickel-iron-tungsten alloys were produced by electrodeposition from an ammoniacal citrate bath. The tungsten content of the alloy ranged from 0.8 wt.% to 11 wt.%, and the crystal grain size of the FCC phase of the solid solution ...
Ćirović Nataša +5 more
doaj +1 more source
Effect of the degree of plastic deformation on the thermal electromotive force of cu-x5crni1810 steel thermocouple [PDF]
Science of Sintering, 2018 The thermal electromotive force (TEMF) and the thermal electromotive force coefficient (TEMFC) of the thermocouple consisting of a copper wire and an (X5CrNi1810) steel wire plastically deformed under tension or bending conditions were found to ...
Milićević Ivan +4 more
doaj +1 more source