Results 71 to 80 of about 147,554 (292)

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi   +4 more
wiley   +1 more source

Charge integration successive approximation analog-to-digital converter for focal plane applications using a single amplifier [PDF]

open access: yes, 1999
An analog-to-digital converter for on-chip focal-plane image sensor applications. The analog-to-digital converter utilizes a single charge integrating amplifier in a charge balancing architecture to implement successive approximation analog-to-digital ...
Pain, Bedabrata, Zhou, Zhimin
core   +1 more source

Audio Cards for High-Resolution and Economical Electronic Transport Studies

open access: yes, 2012
We report on a technique for determining electronic transport properties using commercially available audio cards. Using a typical 24-bit audio card simultaneously as a sine wave generator and a narrow bandwidth ac voltmeter, we show the spectral purity ...
Bedau, Daniel   +2 more
core   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

open access: yesAdvanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek   +5 more
wiley   +1 more source

3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs

open access: yesAdvanced Engineering Materials, EarlyView.
This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu   +4 more
wiley   +1 more source

Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley   +1 more source

DSP-Enhanced Analog-to-Digital Conversion for High-Speed Data Centers' Optical Connectivities

open access: yesIEEE Photonics Journal, 2015
As data centers evolve to sustain the economic scale in network traffic, optical interconnections are adapted to support the vast amount of capacity requirements.
Yaron Yoffe, Dan Sadot
doaj   +1 more source

Analog-to-digital conversion techniques for precision photometry [PDF]

open access: yes
Three types of analog-to-digital converters are described: parallel, successive-approximation, and integrating. The functioning of comparators and sample-and-hold amplifiers is explained.
Opal, Chet B.
core   +1 more source

Study of First-Order Thermal Sigma-Delta Architecture for Convective Accelerometers

open access: yes, 2008
This paper presents the study of an original closed-loop conditioning approach for fully-integrated convective inertial sensors. The method is applied to an accelerometer manufactured on a standard CMOS technology using an auto-aligned bulk etching step.
Latorre, Laurent   +3 more
core   +4 more sources

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal   +2 more
wiley   +1 more source

Home - About - Disclaimer - Privacy