Results 121 to 130 of about 165,996,908 (232)
, 2007 The central detector of the KASCADE experiment is equipped with a trigger and timing facility, which enables measurements of the arrival time distributions of muons hitting the central detector.
M. Foller +2 more
core
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley +1 more source
Robust Time-Delay Based Angle of Arrival Estimation
, 2008 The differences in the arrival times of a signal at spatially separated sensors can be used to estimate the angle of arrival of the signal. Due to noise or sensor malfunction, the time difference estimates may be erroneous and thus the angle of arrival ...
core
Advanced Engineering Materials, EarlyView.Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali +5 more
wiley +1 more source
ABSTRACT TIME-DELAY SELECTION FOR ROBUST ANGLE OF ARRIVAL ESTIMATION
, 2008 The differences in the arrival times of a signal at spatially separated sensors can be used to estimate the angle of arrival of the signal. Due to noise or sensor malfunction, the time difference estimates may be erroneous and thus the angle of arrival ...
core
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Angle of arrival of ten centimeter microwaves
, 1955 The path of an electromagentic wave propagated through the earth's atmosphere depends upon the homogeneity of the atmosphere. For the well mixed condition, which is the case most of the time, the wave follows a straight or a smoothly curved path. However,
Nelms, George Leroy Batten
core +1 more source
Advanced Engineering Materials, EarlyView.Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki +2 more
wiley +1 more source
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source