Results 21 to 30 of about 565,913 (252)
Beilstein Journal of Nanotechnology, 2019 We report a simple one-step hydrothermal strategy for the fabrication of a C-MoS2/rGO composite with both large surface area and high porosity for the use as advanced electrode material in lithium–sulfur batteries.
Chengxiang Tian +6 more
doaj +1 more source
East European Journal of Physics, 2020 The study aimed at enhancement and optimisation of SnS conductivity via annealing for field effect transistor’s semiconductor channel layer application. Interstitials and vacancies in SnS films are known to cause carrier traps which limit charge carriers
Thomas Daniel +3 more
doaj +1 more source
Improving parameters of planar pulse diode using gettering
Tekhnologiya i Konstruirovanie v Elektronnoi Apparature, 2021 Pulse diodes are widely used as part of high-frequency pulse circuits. However, it should be noted that the cost of pulsed diodes remains relatively high, due to the low yield of suitable devices when they are sorted according to the criteria of reverse ...
Viktor Litvinenko +3 more
doaj +1 more source
Change In Microstructure and Mechanical Properties Of Four-Layer Stack ARB Processed Complex Aluminum Sheet with Annealing [PDF]
Archives of Metallurgy and Materials, 2021 The four-layer stack accumulative roll bonding (ARB) process using AA1050, AA5052 and AA6061 alloy sheets is performed up to 2 cycles without a lubricant at room temperature.
Sang-Hyeon Jo, Seong-Hee Lee
doaj +1 more source
A Simulated Annealing Method to Cover Dynamic Load Balancing in Grid Environment [PDF]
, 2009 High-performance scheduling is critical to the achievement of application performance on the computational grid. New scheduling algorithms are in demand for addressing new concerns arising in the grid environment.
Herrero Martín, María del Pilar +1 more
core +1 more source
INVESTIGATING THE IMPACT OF ANNEALING TEMPERATURE ON THE MICROSTRUCTURE AND MECHANICAL PERFORMANCE OF SELECTIVELY LASER MELTED Ti6Al4V ALLOY [PDF]
European Journal of Materials Science and Engineering, 2023 This research addresses the metallurgical and mechanical response during the annealing of Ti6Al4V parts fabricated by selective laser melting. The as-manufactured Ti6Al4V exhibited a very fine α´ martensitic structure with low ductility of less than 10%.
Hassanen JABER +4 more
doaj +1 more source
Литьë и металлургия, 2019 The regularities of the formation of powders based on the Fe-Al system, obtained by the method of mechanical alloying and intended for the deposition of thermal spraying coatings were established.
F. G. Lovshenko, A. S. Fedosenko
doaj +1 more source
Effect of Annealing on Microstructure and Capacitance Properties of Sol-gel TiO2 Film on Aluminum
International Journal of Electrochemical Science, 2021 Sol-gel TiO2 film prepared by dip-coating on aluminum was annealed under different temperatures, and subsequently anodized in ammonium adipate solution.
Huifeng Kang +5 more
doaj +1 more source
Mechanical Properties of P92 Welded Joint after 3000 Hours of Annealing at 600 and 650°C [PDF]
Archives of Metallurgy and Materials, 2019 P92 steel is a modern martensitic heat-resistant steel currently used for seamless products for pressure equipment operating in supercritical operating parameters.
K. Sówka +4 more
doaj +1 more source
Gut microbiome and aging—A dynamic interplay of microbes, metabolites, and the immune system
FEBS Letters, EarlyView.Age‐dependent shifts in microbial communities engender shifts in microbial metabolite profiles. These in turn drive shifts in barrier surface permeability of the gut and brain and induce immune activation. When paired with preexisting age‐related chronic inflammation this increases the risk of neuroinflammation and neurodegenerative diseases.
Aaron Mehl, Eran Blacher
wiley +1 more source