Results 31 to 40 of about 401,901 (235)
Оptimization of the chrome plating bath operation during the restoration of vehicle parts
Вестник СибАДИ, 2021 Introduction. In the process of chrome plating of car parts, there is a change in the composition of the chrome plating bath, which affects the stability of the ongoing processes – the performance and quality of the chrome coating.
A. N. Kotomchin
doaj +1 more source
Real-time monitoring of proton exchange membrane fuel cell stack failure [PDF]
, 2016 Uneven pressure drops in a 75-cell 9.5-kWe proton exchange membrane fuel cell stack with a U-shaped flow configuration have been shown to cause localised flooding.
Brandon, NP +5 more
core +2 more sources
Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution
Advanced Engineering Materials, EarlyView.Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat +5 more
wiley +1 more source
NanomaterialsThe extensive use of sodium-ion batteries has made it important to develop high-performance anode materials. Owing to their good sustainability, low cost, and excellent electrochemical properties, hard carbon materials are expected to be a good choice ...
Yuanfeng Liu +5 more
doaj +1 more source
Solid oxide fuel cell with an anode incorporating a BaCe0.8Y0.2O3-α proton conductor
Mechanical Engineering Journal, 2014 A new type of anode incorporating the proton conductor BaCe0.8Y0.2O3-α (BCY) was fabricated and proposed for a high-power solid oxide fuel cell (SOFC).
Kohei MASUDA +2 more
doaj +1 more source
Using Highly Flexible SbSn@NC Nanofibers as Binderless Anodes for Sodium-Ion Batteries
Surfaces, 2023 Flexible and binderless electrodes have become a promising candidate for the next generation of flexible power storage devices. However, developing high-performance electrode materials with high energy density and a long cycle life remains a serious ...
Jiaojiao Liang +8 more
doaj +1 more source
Nonflammable Lithium Metal Full Cells with Ultra-high Energy Density Based on Coordinated Carbonate Electrolytes [PDF]
, 2020 Coupling thin Li metal anodes with high-capacity/high-voltage cathodes such as LiNi0.8Co0.1Mn0.1O2 (NCM811) is a promising way to increase lithium battery energy density. Yet, the realization of high-performance full cells remains a formidable challenge.
Borodin, Oleg +6 more
core +1 more source
Advanced Engineering Materials, EarlyView.In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart +3 more
wiley +1 more source
ANODES FOR SOFC: REVIEW OF MATERIAL SELECTION, INTERFACE AND ELECTROCHEMICAL PHENOMENA [PDF]
Química NovaThis paper presents a comprehensive interface and electrochemical phenomena review of different anodes for SOFC. In this way, it was possible to select some mixed electronic and ionic conductor materials alternatives to the conventional anode, Ni-YSZ ...
Marina Curi +4 more
doaj +2 more sources
Treatment of waste sulfuric acid copper electrolyte [PDF]
Mining and Metallurgy Engineering Bor, 2014 The aim of this paper was to investigate the possibility of using the copper anodes with high nickel content for electrolytic treatment of waste sulfuric acid copper electrolyte. Nickel content in each anode was about 10 wt. %.
Marković Radmila +3 more
doaj +1 more source