Results 211 to 220 of about 171,290 (313)

Near-UVA Radiation at 405 nm: Germicidal Effect With and Without Sub-Lethal Conditions on Gram-Positive and Gram-Negative Bacteria. [PDF]

Pathogens
Amodeo D, Pedrazzoli G, Palma I, Puccio A, Trillocco G, Papale G, Cevenini G, Tani M, Messina G.   +8 more
europepmc   +1 more source

Comparison of stress distribution around splinted and nonsplinted implants with different crown height space in posterior mandible: A finite element analysis study

Journal of Prosthodontics, EarlyView.
Abstract Purpose The purpose of this finite element analysis (FEA) study was to analyze the stress distribution on prosthetic components of splinted and nonsplinted prostheses, bone, and implants with different crown height space (CHS). Materials and Methods Mandibular posterior segment was modeled with no resorption at the second premolar site and ...
Hamiyet Güngör Erdoğan, Mert Keleş, Burak Yılmaz   +2 more
wiley   +1 more source

A novel electronic key-controlled expander for precise asymmetric palatal expansion. [PDF]

Front Dent Med
Alhazmi N.
europepmc   +1 more source

Finite element analysis of primary healing implants with different transmucosal designs

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aimed to assess the response of peri‐implant tissues, both hard and soft, to mechanical stress when using a primary healing implant (PHI) with two different transmucosal profiles: concave (Model A) and divergent (Model B). The investigation also sought to observe bone modeling under post‐extraction conditions.
Mario Ceddia, Tea Romasco, Luca Comuzzi, Alessandro Cipollina, Adriano Piattelli, Natalia Di Pietro, Bartolomeo Trentadue   +6 more
wiley   +1 more source

Aerodynamic performance enhancement of Archimedes spiral wind turbine blades through surface modifications: A numerical and experimental study. [PDF]

Sci Rep
Faisal AE, Lim CW, Abdulameer Jabbar Al-Quraishi B, Milano J, Hong TC, Chen CP.   +5 more
europepmc   +1 more source

Biomechanics of the implant‐supported full arch fixed complete denture manufactured by milling and injection techniques: An experimental and FEA study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aims to characterize the mechanical properties of implant‐supported full arch fixed complete dentures manufactured by milling and injection techniques. Materials and Methods Twenty‐two samples with milling and injection manufacturing techniques were fabricated.
Mustafa Gürkan, Ovul Kumbuloglu, Makbule Heval Şahan, Mert Narin, Halis Kandaş, Yusuf Arman, Hasan Yildiz, Mahmut Pekedis   +7 more
wiley   +1 more source

Investigation of drag models for simulation of gas-liquid two-phase flow systems. [PDF]

Sci Rep
Adzaklo SY, Sarkodie K, Agyei E, Yamoah S, Asiedu NY.   +4 more
europepmc   +1 more source

Can an increase in abutment screw length enable biomechanical advantages for implants with increased crown height space?

Journal of Prosthodontics, EarlyView.
Abstract Purpose The purpose of this finite element analysis (FEA) study was to investigate how screw length and crown height affect the stresses generated in the implant‐abutment complex and alveolar bone for anterior single implants and whether the use of longer abutment screw would compensate for increased stresses originated from increased crown ...
Mert Keleş, Hamiyet Güngör Erdoğan, Burak Yılmaz   +2 more
wiley   +1 more source

Development of a novel solar system incorporating a heat pipe within a porous enclosure for simulating paraffin melting. [PDF]

Sci Rep
Sheikholeslami M, Sarmadi MJ, Momayez L, Ashorynejad HR.   +3 more
europepmc   +1 more source