Results 41 to 50 of about 197,138 (356)
DESIGN OF INDUCTION COIL FOR OXYGEN FREE COPPER PRODUCTION
Journal of Engineering and Sustainable Development, 2021 This paper deals with the design of an induction coil (IC) intended to be used for an oxygen free copper production. This coil differs in design because it should be placed in a vacuum or in a chamber filled with noble gas, such as Argon.
Murtadha S. Kazem, Isam M. Abdulbaqi
doaj +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Einsatz von ANSYS beim Entwurf von Sensoren in der Mikrosystemtechnik
, 2022 Es werden Probleme und Ergebnisse beim Einsatz des Programms ANSYS bei der Entwicklung von Sensoren in der Mikrosystemtechnik diskutiert. Betrachtet werden ein Sensor zur Bestimmung von Druckdifferenzen, ein mechanischer Sensor zur Analyse von ...
Erlebach, A., Müller, M., Kunze, D.
core
Manual de diseño de puentes mediante el software de ingeniería ANSYS WORKBENCH 2020 R2 [PDF]
, 2021 En la vía que comunica la ciudad de Pereira con el municipio de Marsella se encuentra ubicado el puente Curtiembres, el cual con el paso del tiempo y el incremento de vehiculos de carga que transitan por allí, se ha venido deteriorando, y por ...
Grajales Bermúdez, Jeison Steven
core
Advanced Engineering Materials, EarlyView.A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič +7 more
wiley +1 more source
Вестник СибАДИ, 2018 Introduction. This article deals with the problem of moisture condensation inside the cabin of the technological electric transport vehicle. The hypothesis of using the forced air ventilation in the cabin is substantiated, by which such problem could be ...
N. M. Filkin, A. M. Tatarkin
doaj +1 more source
Optimal Design of Power Transformer with Advance Core Material using ANSYS Technique
, 2020 Due to indulge behavior of core materials and losses that leads to degradation of transformer efficiency. This research paper evaluating the optimal performance of transformer with designing of a newly core material namely as Mo.Me6.
S. Urooj +3 more
semanticscholar +1 more source
Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion
Advanced Engineering Materials, EarlyView.Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello +7 more
wiley +1 more source
Fracture and Structural Integrity, 2023 In this paper, an experimental and numerical study was achieved to investigate the behavior of masonry beams internally reinforced using carbon fiber-reinforced polymer (CFRP) and hybrid steel/CFRP reinforcements.
Mahmoud Zaghlal +3 more
doaj +1 more source
Topologieoptimierung mit Ansys AIM und Ansys Workbench
, 2018 Durch die neue Schweißfunktionalität in Creo 4, welche es ermöglicht Schweißnähte als Volumengeometrie zu modellieren, entstehen viele neue Möglichkeiten zur Berechnung der Spannungen innerhalb der Schweißnähte. Damit einhergehend entstehen neue Möglichkeiten zur Berechnung und Evaluierung dieser Schweißnähte nach den Richtlinien der FKM.
Waidmann, Axel
openaire +2 more sources