Results 51 to 60 of about 117,133 (305)

Finite Element Analysis Up To Failure Of Composite Concrete – Corrugated Steel Cylindrical Shells [PDF]

open access: yesEngineering and Technology Journal, 2009
This study presents three-dimensional finite element analysis to the behavior of composite concrete-corrugated steel cylindrical shell. This type of construction utilizes the advantages of both of ordinary reinforced concrete and the composite action of ...
Husain M. Husain   +2 more
doaj   +1 more source

Nonplanar Bouligand Architectures for Enhanced Mechanical Performance in Cementitious Composites

open access: yesAdvanced Materials, EarlyView.
Inspired by the impact region of the Mantis shrimp dactyl club, nonplanar additive manufacturing translates sinusoidal Bouligand architectures into cementitious composites. Printing‐induced anisotropy and architected interfaces promote distributed damage and arrest crack propagation, enhancing strength and energy absorption.
Yu Wang   +7 more
wiley   +1 more source

A Study of Eddy currents in a Linear Induction Furnace Using Finite Element Method [PDF]

open access: yesEngineering and Technology Journal, 2005
This paper is concerned with a deep study of the magnetic field intensity distribution and the induced eddy currents in a core ( the work piece ) of a linear induction furnace . Numerical technique is considered in this study based on a general - purpose
Adil Ahmad   +2 more
doaj   +1 more source

Monolithically 3D‐Printed Spectral‐Spatial Meta‐Authenticators

open access: yesAdvanced Materials, EarlyView.
A single height map printed in a low‐index resin by two‐photon lithography encodes multiple visible wavelengths in one metasurface without any polarization optics. A fabrication‐aware optimization folds the printable height levels into the design, so the device is printed as optimized.
Cherry Park   +3 more
wiley   +1 more source

Evaluation of Transverse Construction Joints of Reinforced Concrete Beams [PDF]

open access: yesEngineering and Technology Journal, 2010
Construction joints are stopping places in the process of placing concrete, and they are required because in many structures it is impractical to place concrete in one continuous operation.
Qais Abdul-Majeed
doaj   +1 more source

Comparative Study of Residual Stress Prediction Methods in Additive Manufacturing Processes

open access: yesCommunications, 2022
The additive manufacturing (AM) of products involves various processes, such as raising the temperature of a work-piece (part) and substrate to the melting point and subsequent solidification, using a movable source of heat.
Suyambazhahan Sivalingam   +4 more
doaj   +1 more source

Liquid‐Crystal‐Based Reconfigurable Intelligent Surface for 7 GHz Mobile Communication

open access: yesAdvanced Materials Technologies, EarlyView.
The glass‐based liquid‐crystal reconfigurable intelligent surface (LC‐RIS) integrates active‐matrix driving and blind‐greedy phase optimization within a 5G‐NR OFDM framework. This enables continuously tunable and autonomous enhancement of wireless coverage. Leveraging the transparency and manufacturability of liquid crystal panels, it is ideally suited
Tien‐Lun Ting   +5 more
wiley   +1 more source

Adjoint-Driven Inverse Design of a Quad-Spectral Metasurface Router for RGB-NIR Sensing

open access: yesNanomaterials
There has been an increasing demand for high-resolution image sensing technologies in recent years due to their diverse and advanced optical applications.
Rishad Arfin   +4 more
doaj   +1 more source

Influence of the Butt Joint Design of TIG Welding on the Thermal Stresses [PDF]

open access: yesEngineering and Technology Journal, 2011
The aim of this paper is to demonstrate the influence of the single butt joint design of TIG welding on the thermal stresses for carbon steel type St-37.
Hani Aziz Ameen   +2 more
doaj   +1 more source

Short and Length‐Independent Group Delay Supported by Topological Edge States in Finite‐Size Su–Schrieffer–Heeger Chains

open access: yesAdvanced Materials Technologies, EarlyView.
This study demonstrates short, length‐independent group delay supported by topological edge states in open Su–Schrieffer–Heeger networks. Strong boundary port coupling enables an order‐of‐magnitude latency reduction compared to bulk modes, alongside robust protection against bulk disorder.
Yu‐Han Chang   +11 more
wiley   +1 more source

Home - About - Disclaimer - Privacy