Results 61 to 70 of about 134,379 (256)
Analysis of the Flow Around the Wind Turbine Profile for Small Reynolds Number. [PDF]
, 2013 Celem pracy było wykonanie obliczeń dla opływu profilu aerodynamicznego NACA0018 stosowanego w turbinach wiatrowych małej mocy o pionowej osi obrotu. Do numerycznego modelowania przepływu został wykorzystany program ANSYS CFX. Wyniki obliczeń porównano z
Smolny, Antoni, Wiklak, Piotr
core
Optimizing of metal foam design for the use as a heat exchanger [PDF]
, 2018 The work deals with possibilities of using this specific material. It is focused on cast metal foams with a regular arrangement of internal cells and it refers to already used casting technologies - the production of metal foamswith the aid of sand cores.
Gebauer, Marek +2 more
core +1 more source
, 2017 Computational Fluid Dynamics (CFD) methods are widely used for centrifugal compressors design and flow analysis. The calculation results are dependent on the chosen software, turbulence models and solver settings.
Y. Galerkin, I. Voinov, A. Drozdov
semanticscholar +1 more source
Numerical Investigation of Transonic Axial Compressor Rotor With Leading‐Edge Tubercles
Engineering Reports, Volume 8, Issue 3, March 2026.Amplitude, wavelength, and span‐wise location of the leading‐edge tubercles on a transonic NASA Rotor 37 compressor are numerically optimized. An increase in efficiency by 0.52% compared to the corresponding baseline rotor is observed. The location of the shockwave moves downstream of the rotor with 1.91% higher pressure.
Muhammad Hamza +6 more
wiley +1 more source
MODELLING OF INFLUENCE OF TURBULENT TRANSITION ON HEAT TRANSFER CONDITIONS
TASK Quarterly, 2008 This article deals with the turbulent transition phenomenon modelling and its influence on heat transfer. The purpose of the analyses was to verify the transition modelling implemented in the ANSYS CFX 11 commercial code for popular test cases (low flow
KRZYSZTOF BOCHON +2 more
doaj
Flow Rate Analysis of 3/2 Directional Pneumatic Valve by Means Of Ansys Cfx Software [PDF]
Transactions of the VŠB-Technical University of Ostrava, Mechanical Series, 2014 The main purpose of this paper was to develop a selection method of the pneumatic connectors for directional 3/2 valve. The method was established to minimize resistance and loss of pressure in the valve with mounted pneumatic connections for the ...
Slawomir BLASIAK +2 more
doaj +1 more source
Experimental and Numerical Investigation of Thermal Performance of a Crossed Compound Parabolic Concentrator with PV Cell [PDF]
, 2016 Crossed compound parabolic concentrator (CCPC) is a solar energy device used to increase the photovoltaic (PV) cell electrical power output. CCPC’s thermal and optical performance issues are equally important for a PV cell or module to work under a ...
Knox, A.R. +4 more
core
Innovative Fluid Mechanics Education Through Augmented Reality and Interactive Learning
Proceedings in Applied Mathematics and Mechanics, Volume 26, Issue 1, March 2026.ABSTRACT Traditional pedagogical setups in laboratories are often outdated and do not provide the necessary support for effective learning. Teaching fluid mechanics poses additional significant challenges, particularly due to the need to visualize invisible properties, like velocity vector fields (velocity) or scalar pressure fields in time‐dependent ...
Alexander S. Behr +7 more
wiley +1 more source
Numerical modeling of horizontal stratified two-phase flows using the AIAD model
Frontiers in Energy Research, 2022 In nuclear reactor safety research, the countercurrent gas-liquid two-phase flow in the hot leg of a pressurized water reactor (PWR) has attracted considerable attention.
Hongjie Yan +5 more
doaj +1 more source
Jet pumps for thermoacoustic applications: design guidelines based on a numerical parameter study [PDF]
, 2015 The oscillatory flow through tapered cylindrical tube sections (jet pumps) is characterized by a numerical parameter study. The shape of a jet pump results in asymmetric hydrodynamic end effects which cause a time-averaged pressure drop to occur under ...
ANSYS +8 more
core +4 more sources