Results 61 to 70 of about 1,053 (261)

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

WRLS-Driven Robustness Enhancement of Nine-Switch Unified PV-DVR Systems Under Unbalanced Grid Conditions

IEEE Access
Integrated systems combining grid-connected photovoltaic (PV) plants and dynamic voltage restorers (DVR) via nine-switch inverters (NSI) offer a compact and cost-effective solution for power quality enhancement.
Jefferson Rafael Pereira De Assis, Darlan Alexandria Fernandes, Mauricio Beltrao De Rossiter Correa, Alfeu Joaozinho Sguarezi Filho, Fabiano Fragoso Costa, Edison Roberto Cabral Da Silva   +5 more
doaj   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Low-voltage ride-through capability in a DFIG using FO-PID and RCO techniques under symmetrical and asymmetrical faults. [PDF]

Sci Rep, 2023
Sabzevari K, Khosravi N, Abdelghany MB, Belkhier Y, Tostado-Véliz M, Kotb H, Govender S.   +6 more
europepmc   +1 more source

Analysis of the effects of asymmetric faults in three-phase superconducting inductive fault current limiters

Journal of Physics: Conference Series, 2014
Inductive fault current limiters of magnetic shielding type can be described in terms of the excursion in the plane defined by flux linked with primary and line current, and this methodology has been previously applied to single-phase devices. Practical applications, however, require three-phase limiters, which, for the sake of compactness, may be ...
R Ferreira, J M Pina, N Vilhena, P Arsénio, A G Pronto, J Martins   +5 more
openaire   +1 more source

All‐in‐One Analog AI Hardware: On‐Chip Training and Inference with Conductive‐Metal‐Oxide/HfOx ReRAM Devices

Advanced Functional Materials, EarlyView.
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone, Victoria Clerico, Wooseok Choi, Tommaso Stecconi, Folkert Horst, Laura Bégon‐Lours, Matteo Galetta, Antonio La Porta, Nikhil Garg, Fabien Alibart, Bert Jan Offrein, Valeria Bragaglia   +11 more
wiley   +1 more source

Achieving High ON State Current through Ferroelectric Polarization‐Dependent Interfacial Resistance Switching in Undoped Orthorhombic HfO2 Films

Advanced Functional Materials, EarlyView.
Ferroelectric tunnel junction devices based on epitaxial undoped ferroelectric HfO2 films demonstrate stable switching endurance of over 106 switching cycles, low write voltages of ±3 V, 16 measured resistance states, and neuromorphic capability.
Markus Hellenbrand, Nuno Estrócio, Ji S. Kim, Babak Bakhit, Marian C. Istrate, Corneliu Ghica, Tiago Rebelo, Nives Strkalj, Abin Varghese, Bernardo Almeida, Luís S. Marques, Bipin Rajendran, Judith L. MacManus‐Driscoll, José P. B. Silva   +13 more
wiley   +1 more source

Time Series-Based Fault Detection and Classification in IEEE 9-Bus Transmission Lines Using Deep Learning

IEEE Access
Transmission line faults present a significant threat to the stability of power systems, potentially causing widespread outages. Timely detection of these faults is essential to prevent substantial disruptions in the power supply.
Somchat Jiriwibhakorn, Shazia Kanwal
doaj   +1 more source

Solution‐Processed Two‐Dimensional Indium Oxide on Sodium‐Embedded Alumina for Reconfigurable Optoelectronic Synaptic Transistors

Advanced Functional Materials, EarlyView.
Wafer‐scale two‐dimensioanl In2Se3 oxidized into InOx on sodium‐embedded beta‐alumina enables multifunctional reconfigurable electronics. Sodium ions accumulate within distinct spatial distribution under drain‐controlle and gate‐controlled operation. Drain‐control operation gives controllability of ultraviolet‐driven optoelectronic synaptic conductance
Jinhong Min, Yonghyun Albert Kwon, Hyunbin Kim, Jihyun Kim, Myeongjin Jung, Jaewon Heo, Gwang Ya Kim, Vlastimil Mazanek, Zdeněk Sofer, In Soo Kim, Jeong Ho Cho, Hyesung Park, Sang Min Won, Joohoon Kang   +13 more
wiley   +1 more source