Results 71 to 80 of about 877,528 (163)

Characteristics of tempering response of austempered ductile iron

Journal of Materials Research and Technology, 2018
Austempered ductile iron (ADI) is produced by an isothermal heat treatment. Tempering is an effective method to increase the toughness and decrease the hardness of ADI.
Bingxu Wang, Gary C. Barber, Chuanlin Tao, Xichen Sun, Xu Ran   +4 more
doaj   +1 more source

Abrasive wear resistance of austempered ductile iron at room temperature

, 2013
The use of austempered ductile iron obtained by heat treating spheroidal-graphite cast iron is very important in the gear industry. However the nature of the bainitic structure, which is used to improve wear resistance, has never been fully identified ...
Schissler, J.M., Brenot, P., Chobaut, J.P.   +2 more
core   +2 more sources

Research on Tensile Behaviour of New Structural Material MoNiCa

Medžiagotyra, 2019
This article presents the results of a set of innovative research to analyse a new structural material – steel like austempered ductile cast iron with mechanical properties similar to heat-treated steel, and with technological and exploitation ...
Aliaksandr BAHDANOVICH, Regita BENDIKIENE, Ramunas CESNAVICIUS, Antanas CIUPLYS, Vytautas GRIGAS, Audrius JUTAS, Dzianis MARMYSH, Aleh MAZALEUSKI, Aleh NASAN, Liudmila SHEMET, Sergei SHERBAKOV, Kestutis SPAKAUSKAS, Leonid SOSNOVSKIY   +12 more
doaj   +1 more source

Machining characteristics of Austempered Ductile Iron (ADI)

, 2008
Machining characteristics of Austempered Ductile Iron ...
Guy Littlefair (13071435), Ashwin Polishetty (13058856), S Singamneni (13640131)   +2 more
core  

Production of austempered ductile iron gears for transmission cases

, 2005
The investigations presented in this contribution were targeted to replace a gear group made up of SAE 8620 steel in army jeeps with microstructural controlled austempered ductile iron, in order to reduce the manufacturing steps.
Sagin, Ahmet, Topuz, Ahmet
core   +1 more source

Microstructure and Dry/Wet Tribological Behaviors of 1% Cu-Alloyed Austempered Ductile Iron. [PDF]

Materials (Basel), 2023
Hsu CH, Lin CY, You WS.
europepmc   +1 more source

Development and Wear Analysis of Carbidic Austempered Ductile Iron (CADI) [PDF]

, 2020
: The abrasion wear resistance of iron is improved by the incorporation of an extra phase in the matrix, typically consist of carbides. The objective of the present work is to produce carbides in a ductile cast iron which is subsequently austempered, to ...
S A Patil, Ph D Scholar, Ajay Likhite, S U Pathak   +3 more
core  

Abrasive Wear of Mining Chain Drums Made of Austempered Ductile Iron in Different Operating Modes. [PDF]

Materials (Basel), 2022
Wieczorek AN, Wójcicki M, Drwięga A, Tuszyński W, Nuckowski PM, Nędza J.   +5 more
europepmc   +1 more source

Structural and Phase Analysis of the Ausferritic Ductile Cast Iron Matrix Obtained by Heat Treatment and in the Raw State

C
This paper presents a comparative analysis of ausferritic ductile cast iron matrix obtained through heat treatment and in its raw state. Ausferrite without heat treatment was achieved by modifying the chemical composition, while nodular graphite was ...
Leszek Klimek, Grzegorz Gumienny, Bartłomiej Januszewicz, Radomir Atraszkiewicz, Katarzyna Buczkowska   +4 more
doaj   +1 more source

Properties and Structure of High-Silicone Austempered Ductile Iron

Archives of Foundry Engineering, 2014
The results presented in this paper are a continuation of the previously published studies. The results of hest treatment of ductile iron with content 3,66%Si and 3,80% Si were produced.
Krzyńska A., Kochański A.
doaj   +1 more source