Results 51 to 60 of about 34,890 (264)
Crystals, 2022 Laser shock peening of cold rolled Nitinol was carried out at high power density (7 and 9 GW/cm2) and high overlap ratio (90%). Tensile surface residual stresses were generated in the peened material.
Rajesh Dora Tamiridi +6 more
doaj +1 more source
Characterisation and Development of Nanostructured, Ultrahigh Strength, and Ductile Bainitic Steels [PDF]
, 2006 The purpose of the present work was to characterise and further develop a novel nanostructured type of bainitic steel. Three chemical compositions were considered with different concentrations of Al and Co.
Sherif MY, Sherif, Mohamed
core +2 more sources
Fostering Innovation: Streamlining Magnetocaloric Materials Research by Digitalization
Advanced Engineering Materials, EarlyView.Magnetocaloric cooling (MCE) is an environmentally friendly refrigeration method with great potential. Optimizing MCE materials involves the preparation and screening of large quantities of samples, which in turn generates a large amount of data. A digitalization approach is presented that uses ontologies, knowledge graphs, and digital workflows to ...
Simon Bekemeier +17 more
wiley +1 more source
Metals, 2021 The wear behavior of AISI304 stainless steel was investigated under dry, water-, and oil-lubricated conditions. A block-on-disk wear test was conducted in this work, since the test conditions could be controlled easily.
Yoon-Seok Lee +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig +2 more
wiley +1 more source
Фізика і хімія твердого тіла, 2021 The article deals with tribochemical influence of the surface activity of biosynthetic oils on the operational efficiency and reliability of lubricated friction nodes under the critical conditions.
V.I. Kyrychenko +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source