Results 181 to 190 of about 14,485 (279)

Bioinspired 3D‐Printed NiTi Metamaterials With Bivalve‐Like Crossed‐Lamellar Structures

Rare Metals, Volume 45, Issue 4, April 2026.
ABSTRACT Metamaterials demonstrate unique mechanical properties and functional performance owing to their distinctive topological spatial structures. In this study, by mimicking the natural Saxidomus purpuratus shell, bioinspired crossed‐lamellar architectures with interlamellar apex angles ranging from 60° to 150° were designed and fabricated in NiTi ...
Yu Chen, Zengqian Liu, Weibiao Wu, Haoliang Wang, Shaogang Wang, Hanzhong Liu, Xuegang Wang, Dechun Ren, Haibin Ji, Zhefeng Zhang   +9 more
wiley   +1 more source

Nickel-Titanium Alloys in Endodontics: A Narrative Review. [PDF]

Cureus
Valente P, Sbrenna L, Sbrenna A, Valente F.   +3 more
europepmc   +1 more source

Unveiling Temperature‐Dependent Corrosion Behaviors of FeNiCrMoCBY Amorphous Alloy Coatings In Spent‐Fuel Storage Environments

Rare Metals, Volume 45, Issue 4, April 2026.
ABSTRACT A comparative study was performed to elucidate the temperature‐dependent corrosion kinetics and the semiconductor/structural characteristics of the passive film formed on Fe40Ni7Cr17Mo12C13B9Y2 (at%) amorphous alloy coatings. The results indicate that increasing temperature accelerates the corrosion kinetics of the coating.
Yang Lv, Jing Di, Nan Wang, Hongge Li, Qiang Li, Houyi Bai, Jinbiao Huang, Zihang Wang, Zehao Li, Hongbo Fan, Zhiliang Ning, Jianfei Sun, Yongjiang Huang   +12 more
wiley   +1 more source

Effects of Tensile Specimen Geometry and Gripping System on the Mechanical Stability of Ausferrite in Austempered Ductile Irons. [PDF]

Materials (Basel)
Fu L, Schiralli M, Vedani M, Olofsson J, Górny M, Govahi P, Donnini R, Losurdo M, Angella G.   +8 more
europepmc   +1 more source

Amorphous Hydrogenated Silicon Carbide Interlayers: Chemical, Optical, and Tribological Behavior for Improving Adhesion of Carbon‐Based Films to Ferrous Alloy

Surface and Interface Analysis, Volume 58, Issue 4, Page 246-261, April 2026.
ABSTRACT Diamond‐like carbon thin films have been gaining attention in the last years due to their unique properties, such as low friction coefficient and high wear resistance. However, the lack of adhesion between DLC coatings and ferrous alloys complicates their wider industrial application.
Vanessa Piroli, Michael Cristian Goldbeck, Jennifer Stefani Weber, Felipe Cemin, Bruna Louise Perotti, Carla Daniela Boeira, Fernando Alvarez, Newton Kiyoshi Fukumasu, Antonio Ricardo Zanatta, Alexandre Fassini Michels, Carlos Alejandro Figueroa   +10 more
wiley   +1 more source

The Influence of Initial Microstructure on the Microstructure and Mechanical Properties of Ductile Iron After Nanostructurisation Heat Treatment. [PDF]

Nanomaterials (Basel)
Skołek E, Skoczylas P, Wasiluk K, Świątnicki WA, Wieczorek AN, Myszka D.   +5 more
europepmc   +1 more source

Numerical Prediction of Deformation‐Induced Martensitic Transformation in Cold‐Sprayed Austenitic Stainless Steel

steel research international, Volume 97, Issue 4, Page 2241-2249, April 2026.
Cold spray deposition of stainless steel (grade: SS304) is evaluated for marine applications, with emphasis on martensitic transformation during impact. Analytical modeling, simulations, and experiments reveal that helium‐assisted spraying of fine powders promotes cooling below the martensitic start temperature, enabling up to ≈40% austenite to ...
Cal Vin Wong, K. R. Ramkumar, Sougata Roy, Victor K. Champagne, John J. Lee   +4 more
wiley   +1 more source

Protection of metal interfaces against hydrogen-assisted cracking. [PDF]

Nat Commun
Hachet G, Wei S, Tehranchi A, Dong X, Lestang J, Zhang A, Sun B, Zaefferer S, Gault B, Ponge D, Raabe D.   +10 more
europepmc   +1 more source

Cyclic Plastic Material Behavior of Novel Austenitic (C + N) Steel Additively Manufactured by PBF‐LB/M

Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 4, Page 1313-1326, April 2026.
ABSTRACT The newly introduced high manganese high strength (C + N) steel Printdur HSA was developed for the additive manufacturing process PBF‐LB/M. It consists of a fully austenitic grain structure. This study aims to evaluate the cyclic plastic material behavior of this (C + N) steel.
Jakob Blankenhagen, Mohammad Abankar, Johannes Diller, Dorina Siebert, Christina Radlbeck, Tomáš Kruml, Martin Mensinger   +6 more
wiley   +1 more source

Impact of Substrate Preheating on Weld Quality, Microstructure, Corrosion Resistance, and Mechanical Properties in Gas Tungsten Arc Welding of UNS S32750 Super Duplex Stainless Steel. [PDF]

Materials (Basel)
da Cruz Junior EJ, Ribeiro RH, Varasquim FMFA, Carvalho FO, Santiago LFF, Lemos GP, Ventrella VA, Calliari I.   +7 more
europepmc   +1 more source