Results 51 to 60 of about 4,684 (195)
steel research international, EarlyView.This study validates a recycling pathway for converting interconnect assemblies from end‐of‐life SOC stacks into commercial‐grade AISI 304 steels. Using scrap‐based steelmaking operations, austenitic cast steels with <4.0% δ‐ferrite are successfully produced.
Jeraldine Lastam +7 more
wiley +1 more source
Exploiting Residual Elements Arising from Scrap Steel in Future Sustainable Steel Alloy Design
steel research international, EarlyView.Herein, the effects of residual elements Cu and Sn on grain growth, recrystallization, and phase transformation in C–Mn steel are summarized, and a case study is presented on how the presence of residual elements can be exploited to reduce deliberate Nb microalloying while achieving the same grain size control and strength during thermomechanical ...
Claire Davis +5 more
wiley +1 more source
OPTIMIZATION OF SURFACE ROUGHNESS OF AISI 304 AUSTENITIC STAINLESS STEEL IN DRY TURNING OPERATION USING TAGUCHI DESIGN METHOD [PDF]
Journal of Engineering Science and Technology, 2010 The present work is concentrated with the dry turning of AISI 304 Austenitic Stainless Steel (ASS). This paper presents the influence of cutting parameters like cutting speed, feed rate and depth of cut on the surface roughness of austenitic stainless ...
D. PHILIP SELVARAJ, P. CHANDRAMOHAN
doaj
Engineering and Applied Science Research, 2022 This study investigated changes in the average grain size and hardness values of 253 MA austenitic stainless steel (ASS) and determined the grain growth kinetics as well as a hardness empirical model. A 35% multi-pass cold rolling process was employed to
Rana K. Melinia +3 more
doaj
steel research international, EarlyView.Heat treatments that alter the proportions of austenite and ferrite phases or induce the precipitation of phases such as sigma in duplex stainless steel UNS S32205 make it more susceptible to pitting and crevice corrosion. However, the effects of these treatments are not always evident when analyzed using the cyclic polarization technique.
Alba Regina Turin +8 more
wiley +1 more source
Microstructure and Properties of Low-nickel Austenitic Stainless Steel14.0Cr-1.1Ni-9.2Mn-0.30Cu
Teshugang, 2023 14.0Cr- 1. 1Ni-9.2Mn-0.30Cu stainless steel was developed on the basis of13.36Cr- 1. 12Ni- 11.2Mn low-nickel austenitic stainless steel, and the metallographic structure, microstructure, mechanical properties and forming properties of austenitic ...
吴海林 +4 more
doaj
steel research international, EarlyView.This study uses in situ synchrotron X‐ray diffraction at the German Electron Synchrotron to analyze low‐pressure carburizing (LPC) in steels. The findings reveal surface carbon saturation and carbide formation kinetics, and phase‐specific stress development during quenching. The results show carbide kinetics depend on steel grade and size, while stress
Ogün Baris Tapar +6 more
wiley +1 more source
Numerical Simulation of the Strength and Plasticity Performance in Austenitic Stainless Steel
High Temperature Materials and Processes, 2013 The effect of temperature and alloy content on the strength and plasticity of austenitic stainless steel was investigated in this paper. A series of expressions for quantitative calculation via computer were obtained according to the experimental data ...
Li Dongsheng, Dai Qixun, Cheng Xiaonong
doaj +1 more source
steel research international, EarlyView.Laser welding of duplex stainless steel disrupts phase balance, promotes nitride precipitation, and reduces fatigue resistance. Postweld heat treatment restores austenite and dissolves nitrides, but the resulting crystallography and phase morphology still impair fatigue performance.
Aparecida Silva Magalhães +6 more
wiley +1 more source
Effect of Adding Copper Foils on Seam Welding Joints of 304 Austenitic Stainless Steel
Diyala Journal of Engineering Sciences, 2014 The aim of this work is to study the effect of adding copper (C10200 AISI) foils on the welding joint of the austenitic stainless steel type (AISI 304).The austenitic stainless steel has low weldability by resistance welding where the concentrated ...
Ammar Azeez Mahdi +2 more
doaj +1 more source