Results 81 to 90 of about 3,958,203 (279)

Surface modification of 3D‐printed polycaprolactone scaffolds with silk fibroin for bone tissue engineering

open access: yesFEBS Open Bio, EarlyView.
Coating 3D‐printed PCL scaffolds with silk fibroin can improve biocompatibility and bone cell adhesion. One innovative design for tissue‐engineering scaffolds uses 3D printing technology. Here, we used polycaprolactone (PCL) filament as a biocompatible material to design a porous 3D scaffold for bone tissue engineering.
Hamed Koeini   +7 more
wiley   +1 more source

Study on the Mechanical Properties and Calculation Method of the Bearing Capacity of Concrete-Filled Steel Pipes under Axial Pressure Load

open access: yesDesigns
Circular steel pipe concrete can give full play to the combination of steel pipes and concrete, resulting in an improvement in the steel pipe’s concrete bearing capacity and ductility.
Xin Liu, Jisheng Hu, Yuzhou Zheng
doaj   +1 more source

Early Clinical, Imaging, and Pathological Characteristics of SRPK3/TTN‐Digenic Myopathy

open access: yesAnnals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective SRPK3/TTN‐digenic myopathy was recently established as a skeletal muscle myopathy caused by digenic inheritance. This study characterizes the early clinical presentation of SRPK3/TTN‐digenic myopathy in one previously reported and seven newly identified pediatric patients.
Rotem Orbach   +23 more
wiley   +1 more source

Association Between Motor Pathway Damage and Motor Deficit in Upper and Lower Limb in People With MS

open access: yesAnnals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective Corticospinal tract damage is common in people with MS, but the degree of clinical symptoms varies. We hypothesize that corticospinal tract lesions are more extensive and severe in people with MS with motor impairments in both upper and lower limbs.
Mathilde Liffran   +13 more
wiley   +1 more source

The method for calculating the bearing capacity of cold-formed C-Section axial compression member using Direct Strength Method [PDF]

open access: yes, 2023
The paper carried out numerical analysis using experimental and finite element analysis methods to determine the bearing capacity of cold-formed C-section axial compression member.
Jang, Yongsong, an, myongchol, Ju, Suin
core  

Effect of Geopolymer Treatment on the Ultimate Bearing Capacity of Sabkha Soil under Axial Loading

open access: yesScientific Reports
Abstract Saline sabkha soils pose a major challenge for geotechnical engineering because of their low bearing capacity and high settlement potential. The purpose of this research was to evaluate the behavior of stabilized sabkha soil under axial stress after geopolymer treatment utilizing the mix and compact method.
Hamid, Wagdi, Alnuaim, Ahmed
openaire   +2 more sources

T1 Over Squared Proton Density Ratio to Characterize Multiple Sclerosis Lesions

open access: yesAnnals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective Differentiating remyelinated from demyelinated lesions in MS remains challenging without histological confirmation. This study introduces the T1‐to‐PD2 ratio (TPR) imaging approach and evaluates its ability to characterize MS lesions alongside other quantitative MRI (qMRI) metrics. Methods Thirty individuals with MS (mean age: 47.5 ± 
Sarah J. Wright   +10 more
wiley   +1 more source

Cognitive and Neuroimaging Divergence Between Juvenile and Adult FUS Amyotrophic Lateral Sclerosis

open access: yesAnnals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disorder characterized by progressive motor neuron degeneration. Fused in sarcoma (FUS)‐associated juvenile ALS (jALS) represents a distinct and aggressive subgroup with rapid deterioration and poor prognosis.
Alexandra V. Jürs   +7 more
wiley   +1 more source

Research on axial compression performance test and bearing capacity calculation method of newly assembled hollow lattice wallboard

open access: yesFrontiers in Materials
With the great development of the construction industry, prefabricated building components have been greatly developed. To study the compressive performance of the new wallboard, the axial compression performance test of six full-scale new lattice ...
Yunlin Liu   +7 more
doaj   +1 more source

Deep Learning Pose Estimation for Phenotyping of Co‐Occurring Hyperkinetic Movement Disorders

open access: yesAnnals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective To explore whether routine outpatient video combined with deep learning‐based pose estimation and clinically interpretable kinematic features can support multi‐label phenotyping of co‐occurring hyperkinetic movement disorders (HMDs).
Laura Cif   +17 more
wiley   +1 more source

Home - About - Disclaimer - Privacy