Results 111 to 120 of about 189,459 (306)
Phenomenological modeling of strain hardening, phase transformation and damage effects of trip-steels [PDF]
, 2017 In this study, the constitutive modeling of loading state dependent strain hardening and martensite evolution of high alloyed TRIP-steels are addressed, which are experimentally observed comparing uni-axial tension and compression test results ...
Kuna, Meinhard, Seupel, Andreas
core
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Buckling strength of filament-wound cylinders under axial compression is investigated [PDF]
, 1967 Analytical study was made of the effects of axial compression on buckling strength of filament-wound cylinders having diameter-to-wall thickness ratios of 167 to 643.
core +1 more source
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
BioengineeringBackground Context: This study’s purpose was to evaluate the biomechanical performance of plate–nail and dual-plate fixation for the treatment of AO/OTA 41-C2 tibial plateau fractures.
Wei Xie +7 more
doaj +1 more source
Design of reinforced concrete beams with web openings [PDF]
, 2006 The provision of transverse openings in floor beams to facilitate the passage of utility pipes and service ducts results not only in a more systematic layout of pipes and ducts, it also translates into substantial economic savings in the construction of ...
Mansur, M. A.
core
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source
Jixie qiangdu, 2017 The accurate calculation of load-carrying capacity of integrally stiffened panels under axial compression is the key factor for designing and analyzing of wing panel,which is essential for the aircraft wing structural efficiency and weight control,it is ...
LIU Cun, WAN YaFeng, LI Jian
doaj
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source