Results 111 to 120 of about 1,307,206 (279)
Advanced Engineering Materials, EarlyView.Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn +5 more
wiley +1 more source
A Quantitative Study of Axial Performance of Rockbolts with an Elastic–Debonding Model
Applied SciencesFull-length anchorage rockbolts are widely used in roadway reinforcement and rock controlling in underground mining. This article proposes using an elastic–debonding (ED) model to analyse the axial performance of rockbolts. The advantage of this ED model
Jianhang Chen +5 more
doaj +1 more source
Design of a Multistable Finger Prosthesis with Programmable Metamaterials
Advanced Engineering Materials, EarlyView.This research article shows the development of a multistable programmble metamaterial for the use as a finger prosthesis. The material was designed on different hierarchical levels where the influence of geometrical parameters and combination of mechanical elements was explored.
Franziska Wenz +5 more
wiley +1 more source
GAS HOLDUP AND AXIAL LIQUID DISPERSION IN THREE PHASE BUBBLE COLUMNS
Journal of Engineering and Sustainable Development, 2015 Axial liquid dispersion coefficient was studied in air-tap water systems (bubble columns) and air-tap water-PVC solid particles systems for different column diameters, 10, 15, and 30 cm, Each column had a gas distributor plate with perforated holes of
Burhan Sadeq Abdulrazzaq
doaj
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
, 2016 Axial spondyloarthritis is the commonest inflammatory arthritis affecting the spine. Typically first presenting to a variety of primary and secondary care professionals, the high global disease burden of this condition has created a need for increased ...
core
FastNano Liquid: An Automated Platform for Small‐Angle X‐ray Scattering‐Based Materials Discovery
Advanced Engineering Materials, EarlyView.We present FastNano Liquid, an automated small‐ and wide‐angle X‐ray scattering platform for the combined synthesis and characterization of (nano)materials. The platform is coupled to varied reactor workflows for both in situ studies of reaction kinetics and ex situ screening of synthesis conditions to support machine learning‐guided exploration ...
Pierre‐Baptiste Flandrin +16 more
wiley +1 more source
Axial field permanent magnet DC motor with powder iron armature
, 2007 The paper describes a double-gap axial field permanent magnet (PM) dc motor whose double-layer armature wave winding is constructed of copper strips.
Mohammad, Mohammad T. +1 more
core +1 more source
Advanced Engineering Materials, EarlyView.To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe +6 more
wiley +1 more source