Results 131 to 140 of about 2,263,616 (295)
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
On Dispersion of a Reactive Solute in a Pulsatile Flow of a Two-Fluid Model
The present paper is a study on dispersion of reactive solute in an oscillatory flow of a two-fluid, three-layer Casson-Newtonian continuum using Aris-Barton’s approach. A two-fluid model of blood flow has been considered, the fluid in the central region
S. Debnath +3 more
doaj
Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel +2 more
wiley +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley +1 more source
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi +3 more
wiley +1 more source
The ALD precursor bis(trimethylsilyl)selenide is simultaneously a substrate surface inhibitor. It allows for the growth of Sb2Se3 in combination with tris(dimethylamido)antimony, but also silylates surface hydroxyl groups on the substrate if such hydroxyls are present.
Pei‐Chun Liao +9 more
wiley +1 more source
ABSTRACT Chitosan, a polysaccharide upcycled from biowaste, has long promised sustainable, biocompatible, and antimicrobial films and devices, an appeal reinforced by its recent regulatory recognition, with several chitosan‐based antibacterial dressings gaining clearance through the Food and Drug Administration's 510(k) pathway.
Jacopo Nicoletti +16 more
wiley +1 more source
Influence of electric field on the unsteady dispersion coefficient in couple-stress flow
The influence of electric field on unsteady convective diffusion in couple stress flow is studied using a time dependent dispersion model. The electric field, arising as a body couple in the governing equations, is shown to increase the axial dispersion ...
Veena , B. H. +2 more
core +1 more source
Fully additive vertical organic electrochemical transistors (vOECTs) with channel‐length of 226 nm on a 50 µm compostable substrate achieve >106 current modulation and ∼36 mS transconductance. Ion‐selective integration enables 1.1 mA dec−1 sensitivity and 36 µm detection limit, highlighting a scalable platform for sustainable electronics and ...
Giulia Frusconi +3 more
wiley +1 more source

