Results 81 to 90 of about 13,095 (260)

Automated Hand Flexor Tendon–Thickness Measurement in Systemic Sclerosis

Arthritis Care &Research, EarlyView.
Objective Systemic sclerosis (SSc) can affect flexor tendons, contributing to hand function problems and reduced quality of life. Tendon changes are currently assessed with ultrasonography and measured manually, a time‐consuming process prone to interobserver variability.
Mark Greveling, Ties van het Erve, Yvette van de Berg, Simon Mastbergen, Julia Spierings   +4 more
wiley   +1 more source

Unsupervised Machine Learning Identifies Shared Biomechanical and Clinical Variation in Individuals with Knee Osteoarthritis and High BMI: A Secondary Analysis of the IDEA Trial

Arthritis Care &Research, Accepted Article.
Objective High body mass index (BMI≥27 kg/m2) and aberrant gait biomechanics are primary risk factors for knee osteoarthritis (KOA), yet the specific loading patterns linked to clinical disease features remain unclear. Unsupervised machine learning (ML) was used to identify vertical ground reaction force (vGRF) waveform modes of variation and ...
Ashley N. Buck, J. Elyse Borgert, Hyeon Lee, Liubov Arbeeva, Yvonne M. Golightly, Richard F. Loeser, Leigh F. Callahan, Stephen P. Messier, Brian Pietrosimone, Amanda E. Nelson, James S. Marron   +10 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Effects of Height to Diameter Ratio and Aeration rate on Liquid Mixing and Hydrodynamic Properties in a Bubble Column [PDF]

Iranian Journal of Chemical Engineering, 2009
"> Experimental measurements of overall gas holdup (εg), residence time distribution (RTD) and liquid mixing time (tm) have been carried out in an air-water system in a 17 lit bubble column with an 11 cm diameter, over a wide range of superficial gas ...
doaj  

Axial Dispersion Coefficient and Mass Transfer Rate in Pulsed Column [PDF]

Journal of Nuclear Science and Technology, 1989
MATSUMOTO, Shiro, HONMA, Shunji, KOGA, Jiro, KOBAYASHI, Hidehiko   +3 more
openaire   +1 more source

A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions

Advanced Engineering Materials, EarlyView.
This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice, Krzysztof S. Stopka, Michael D. Sangid   +2 more
wiley   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Flexural Behavior of 3D‐Printed Porous Bouligand‐Structured Polymers: Influence of Pitch Angle and Porosity

Advanced Engineering Materials, EarlyView.
This study examines how helicoidal architectures with different porosities respond to bending. Adjusting layer angle and spacing in 3D‐printed polymers reveals clear tradeoffs between stiffness, strength, and energy absorption. Experiments and simulations highlight designs that distribute stress effectively, offering pathways for optimizing lightweight
Praveenkumar Subhash Patil, Edward D. McCarthy, Parvez Alam   +2 more
wiley   +1 more source

Density Measurement of Irradiated and Nonirradiated Zirconium Oxide by Ptychographic X‐Ray Computed Tomography (PXCT)

Advanced Engineering Materials, EarlyView.
Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik, Liliana I. Duarte, Malgorzata G. Makowska, Roland Brütsch, Andrej Bullemer, Ana Diaz, Mirko Holler, Andreas Menzel, Johannes Bertsch, Pavel Trtik   +9 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source