Results 201 to 210 of about 93,869 (311)

Aerodynamic shape optimization of axial flow fans

, 1997
The purpose of this work is to improve the efficiency of large scale axial flow fans through the introduction of a more uniform velocity distribution over the fan blades. This improved velocity di tribution being realized through the use of an aerodynamically optimized inlet cone.
openaire   +1 more source

Perspective on Aqueous Batteries: Historical Milestones and Modern Revival

Advanced Materials, EarlyView.
This review retraces the development of aqueous batteries from classical Zn‐MnO2 chemistry to modern Zn and Ni systems, correlating voltage, capacity, and electrolyte formulation with practical performance. By mapping historical success and failure onto current and future research directions, it identifies guiding principles that steer the design of ...
Fangwang Ming, Dong Guo, Yizhou Wang, Hussam Qasem, Hanfeng Liang, Husam N. Alshareef   +5 more
wiley   +1 more source

Value of dynamic contrast-enhanced MRI in the diagnosis of acute radiation-induced rectal injury in patients with rectal cancer: A comparison with endoscopy. [PDF]

Eur J Radiol Open
Fan WJ, Ma YR, Liu QM, Zhang N, Liu YY, Wen ZQ, Lu BL, Yuan JP, Yu SP, Chen Y.   +9 more
europepmc   +1 more source

Piezoelectric Stimulation of Neural Cells: Exploring the Synergistic Potential of Hybrid Scaffolds for Enhanced Regeneration

Advanced Materials Interfaces, EarlyView.
Hybrid piezoelectric scaffolds offer a promising route for Central Nervous System regeneration by combining structural and electrical cues to support neural stem cell growth. This review highlights their potential to overcome current challenges in neural tissue engineering by exploring porous hybrid materials, their biological interactions, and ...
Heather F. Titterton, Chris R. Bowen, Hamideh Khanbareh   +2 more
wiley   +1 more source

Numerical Simulation Study on Non-Axisymmetric Die-Less Spinning with a Right-Angle Groove in the Tube. [PDF]

Materials (Basel)
Ren X, Fan Z, Jia Z, Shen Y, You H.
europepmc   +1 more source

Microenvironment Modulation‐Based Nanomaterial‐Loaded Hydrogel Dressings for Diabetic Foot Ulcers: Research Progress and Future Perspectives

Advanced Materials Interfaces, EarlyView.
xx xx. ABSTRACT Diabetic foot ulcer (DFU) is a chronic complication of diabetes, primarily caused by hyperglycemia, peripheral vascular disease, and neuropathy. Characterized by persistent hyperglycemia, impaired perfusion, inflammation, and infection, DFUs pose significant challenges to healing and are associated with high morbidity and amputation ...
Tang Yuqing, Chen Hong, Fan Weijing, Huang Renyan, You Yang, Liu Guobin   +5 more
wiley   +1 more source

Research on the influence of different heat release rates on the throttling effect and critical wind speed in tunnel engineering. [PDF]

Sci Rep
Luo C, Wang H, Wang Q.
europepmc   +1 more source

Nonmulberry Silk Fibroin Doping Boosts Charge Transfer and Charge Injection in Aligned Polypyrrole‐Silk Scaffolds for Low‐Voltage Neurostimulation

Advanced Materials Interfaces, EarlyView.
Conductive silk‐polypyrrole scaffolds couple redox stability with cell‐affinitive peptides present innately in an endogenous silk fibroin, enabling optimized electrical stimulation to drive neurite outgrowth. Findings establish electrochemical‐biological link for biomaterial design rules for smart nerve guidance conduits that can provide low voltage ...
Rajiv Borah, Joseph Christakiran Moses, Jnanendra Upadhyay, Jitu Mani Das, Michael G. Monaghan, Biman B. Mandal   +5 more
wiley   +1 more source

Primary cerebellar angiosarcoma: a rare case report and literature review. [PDF]

BMC Surg
Wu F, Xu Z, Sun T, Xiao F, Zhang L, Yu S, Zhu Y, Yu J, Zhan R.   +8 more
europepmc   +1 more source

Ultra‐Improved Interfacial Strength Between Metallic Surface and Polyurethane via Cost‐Effective Anodizing Process

Advanced Materials Interfaces, EarlyView.
SAA significantly enhanced Al/PU bonding, increasing SLSS by up to 920% and fracture energy by 15 100% through optimized micro‐nano porous surfaces. RSM identified the optimal anodizing conditions, while ML confirmed sulfuric acid concentration and roughness as dominant predictors of strength.
Umut Bakhbergen, Sherif Araby, Zhandos Tauanov, Nursultan Turdakyn, Reza Montazami, Fethi Abbassi, Gulnur Kalimuldina   +6 more
wiley   +1 more source