Results 101 to 110 of about 671,252 (199)

Hypoplasticity for Sand With Explicitly Defined Asymptotic States

open access: yesInternational Journal for Numerical and Analytical Methods in Geomechanics, EarlyView.
ABSTRACT A hypoplastic model for sand with defined asymptotic states is proposed. The fourth‐order tensor A$\mathsf {A}$ is defined by modifying the compression relation of the reference hypoplastic model by von Wolffersdorff (HP). This enables the mathematical formulation of a hypoplastic model for sand including the asymptotic state boundary surface (
Luis Mugele   +2 more
wiley   +1 more source

Static stiffness calculation and test validation of bushing-type rubber suspension for tracked vehicles

open access: yesJixie qiangdu
ObjectiveAt present, there is no targeted static stiffness calculation method for bushing-type rubber suspensions of tracked vehicles under combined deformation conditions.
LI Ningyi   +3 more
doaj  

High‐Order Pressure–Volume Relationship for Simulation of Stretch and Extrusion Blow Molding Processes

open access: yesPolymer Engineering &Science, EarlyView.
High‐order thermodynamically consistent pressure–volume modeling improves numerical stability and prediction accuracy in stretch and extrusion blow molding simulations. The proposed formulation captures transient pressure evolution and enables reliable thickness prediction with good agreement against experimental measurements.
Z. Benrabah   +3 more
wiley   +1 more source

Polar Fitting and Hermite Interpolation for Freeform Droplet Geometry Measurement

open access: yesMetrology
Droplet-based microlens fabrication using Ultra Violet (UV) curable polymers demands the precise measurement of three-dimensional geometries, especially for non-axisymmetric shapes influenced by electric field deformation.
Mike Dohmen   +2 more
doaj   +1 more source

The iPP Printing Paradox: Interlayer Adhesion Through Crystallization

open access: yesPolymer Engineering &Science, EarlyView.
In fused filament fabrication of isotactic polypropylene, high molecular weight and a high print speed increase the shear during deposition. This shear promotes the formation of the ductile β‐phase at the interphase, which improves interlayer adhesion, as shown by an eightfold increase in fracture energy measured via a T‐peel test on two printed ...
Paul M. H. van Heugten   +5 more
wiley   +1 more source

Study on the Bearing Capacity of Deep Circular Foundation Considering the Axisymmetric Compaction Deformation of Sand Ground

open access: yes工程科学与技术, 2017
:Due to the effects of foundation embedded depth and characteristic of axisymmetric deformation of sand have not been considered simultaneously on the failure mechanism,the Berezantzev's theory for predicting the bearing capacity of a deep circular ...
LIU Guanfei, LEI Shengyou
doaj  

Molecular Basis for Uracil‐DNA‐Glycosylase to Identify DNA Damage in the Nucleosome

open access: yesProteins: Structure, Function, and Bioinformatics, EarlyView.
ABSTRACT The DNA base‐excision repair (BER) pathway is initiated by a glycosylase, such as uracil‐DNA‐glycosylase (UDG), which identifies and removes a wrong base incorporated in the DNA sequence. The very early steps in the identification of the DNA damage are crucial to the correct initiation of the repair chain, and become even more complex when ...
Safwen Ghediri   +2 more
wiley   +1 more source

A study of plastic deformation during axisymmetric forward spiral extrusion and its subsequent mechanical property changes

open access: yes, 2012
Axisymmetric forward spiral extrusion (AFSE) accumulates large strains in its sample while extruding it through a die with engraved spiral grooves.
Peter Hodgson (13089276)   +2 more
core  

Coupled diabatic and frictional forcing of single‐layer vortical flow

open access: yesQuarterly Journal of the Royal Meteorological Society, EarlyView.
A single‐layer balanced model is used to illustrate how diabatic and frictional forcing of a primary balanced vortical flow can be coupled self‐consistently, including the advection of potential vorticity by the induced transverse circulation. The coupling is illustrated in the context of a developing tropical cyclone, in which boundary‐layer dynamics ...
R. K. Scott
wiley   +1 more source

Influence of elastic deformation of tool on sheared part quality in axisymmetric shearing process

open access: yes, 2020
Shearing is one of the most important processes as cutting, because of its high productivity and high yield rate. To get high quality parts, all related process parameters have to be understood and optimized for any applications. However the influence of
Yoshinori Yoshida
core  

Home - About - Disclaimer - Privacy