Results 81 to 90 of about 4,483 (226)

Architecting nano‐Al/HMX/CuO energetic micro‐units unlocks superior interface and highly efficient combustion

open access: yesInfoMat, EarlyView.
Improving the dispersion of nano‐aluminum is of great importance in explosives and propellants. The spherical Al/HMX/CuO energetic micro‐units were prepared using microchannel technology, which significantly improved the uniformity and dispersion of nano‐Al. It also enhanced the mass and heat transfer efficiency between the fuel and oxidizer components,
Gazi Hao   +12 more
wiley   +1 more source

Static stiffness calculation and test validation of bushing-type rubber suspension for tracked vehicles

open access: yesJixie qiangdu
ObjectiveAt present, there is no targeted static stiffness calculation method for bushing-type rubber suspensions of tracked vehicles under combined deformation conditions.
LI Ningyi   +3 more
doaj  

Modeling of Axisymmetric Elastoplastic Deformation of Cylindrical Fibrous Shells

open access: yesМеханика машин, механизмов и материалов, 2018
The problem of elastoplastic axisymmetric deformation is formulated for flexible reinforced circular cylindrical shells under dynamic and quasi-static action of internal excessive pressure.
Andrei P. Yankovskii
doaj  

Grating‐Lens Empowered Metafiber for Large‐Angle Light Collection With 3D Nanoprinted Structures

open access: yesLaser &Photonics Reviews, EarlyView.
A grating‐lens‐based Metafiber enables efficient light coupling into single‐mode fibers at large incidence angles. By combining diffraction and focusing on the fiber facet using a 3D nanoprinted holographic structure, light is selectively coupled only at specific angles while suppressing unwanted signals. This approach achieves high coupling efficiency
Jun Sun, Markus A. Schmidt
wiley   +1 more source

From Planar to 3D Nanophotonic Lenses: Advancing Design, Fabrication, and Applications

open access: yesLaser &Photonics Reviews, EarlyView.
Three‐dimensional nanophotonic lenses are enabled by an integrated workflow that links design parameterization, full‐wave electromagnetic simulation, computational optimization, and freeform fabrication. This Review summarizes how these tools expand optical design freedom beyond a single patterned plane by enriching the local meta‐atom response and ...
Wei Zhu   +2 more
wiley   +1 more source

Polar Fitting and Hermite Interpolation for Freeform Droplet Geometry Measurement

open access: yesMetrology
Droplet-based microlens fabrication using Ultra Violet (UV) curable polymers demands the precise measurement of three-dimensional geometries, especially for non-axisymmetric shapes influenced by electric field deformation.
Mike Dohmen   +2 more
doaj   +1 more source

Design, Analysis, and Experimental Validation of a Variable‐Gap Magnetorheological Damper for Seat Suspension

open access: yesInternational Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT To address the dual challenges of routine driving vibration and impact loads in vehicle seat suspensions, a novel variable‐gap magnetorheological damper (VGMRD) is proposed. By combining a tapered piston with a conformal variable‐diameter cylinder, stroke‐dependent, dual‐mode damping characteristics are achieved without the need for complex ...
Min Wei   +4 more
wiley   +1 more source

Modeling the Elastic Recovery of PET Bottles via a Free‐Blowing of Preforms Campaign

open access: yesPolymer Engineering &Science, EarlyView.
From free‐blown preforms to mechanical properties. ABSTRACT This study aims to quantify the elastic properties induced by biaxial stretching at different temperatures in order to simulate the complete process including the final elastic recovery. The elastic modulus is identified from geometric measurements obtained during free‐blowing experiments. PET
Yun‐Mei Luo, Luc Chevalier
wiley   +1 more source

Microfluidic Capillary Arrays for Pixelated Control of Multimaterial Flows

open access: yesSmall, EarlyView.
A 3D‐printed pixellated capillary array maps up to thousands of fluid inputs into arbitrary multimaterial flow cross‐sections. Automated manifold design and laminar scaling are used to amplify printing resolution orders of magnitude, generating microscale fluidic control from printed elements, enabling designed microflows for potential use in ...
Max Chapman   +2 more
wiley   +1 more source

Home - About - Disclaimer - Privacy