Results 11 to 20 of about 735,720 (116)

High temperature tensile, compression and creep behavior of recycled short carbon fibre reinforced AZ91 magnesium alloy fabricated by a high shearing dispersion technique

open access: yesJournal of Magnesium and Alloys, 2021
The present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys.
Sinan Kandemir   +2 more
doaj   +2 more sources

Tribological Properties of WC-12Co Coating on AZ91 Magnesium Alloy Fabricated by High Velocity Oxy-Fuel Spray

open access: yesHigh Temperature Materials and Processes, 2014
In this study, conventional WC-12Co cermet coatings were deposited on AZ91 magnesium alloy using High Velocity Oxy-Fuel spray method. The effects of different coating thicknesses (60 and 120 µm) and wear loads (20 and 30 N) on tribological properties of ...
Yıldız F.
doaj   +2 more sources

Semi-solid slurry of AZ91 magnesium alloy prepared by electromagnetic stirring near liquidus temperature [PDF]

open access: yesChina Foundry, 2007
An electromagnetic stirring process near liquidus temperature was designed and demonstrated experimentally to produce semi-solid slurry of AZ91 magnesium alloy, in order to avoid not only contamination from mechanical stirring but also the inflammation ...
ZHANG Xiao-li, TENG Hai-tao, LI Ting-ju
doaj   +2 more sources

Effect of Al addition on microstructure of AZ91D [PDF]

open access: yes, 2014
Casting is a net shape or near net shape forming process so work-hardening will not be applicable for improving properties of magnesium cast alloys.
Joshi, U, Babu, NH
core   +5 more sources

Control of Magnesium Alloy Corrosion through the Use of Engineered Intermetallics [PDF]

open access: yes, 2014
The low density and high relative strength of Mg alloys means they can offer engineering benefits over steels or Al alloys. However, the susceptibility of Mg alloys to corrosion has limited their exploitation and restricted their use to more benign ...
Pidcock, Andrew
core   +6 more sources

Friction behavior of laser cladding magnesium alloy against AISI 52100 steel [PDF]

open access: yes, 2012
The use of magnesium alloys in engineering applications is becoming increasingly important as a relatively low density allows savings in energy consumption and therefore reduction in air pollution.
J.E. Masse   +3 more
core   +1 more source

Finite element simulation of magnesium alloys laser beam welding [PDF]

open access: yes, 2010
The authors are grateful to FONDERIE MESSIER (HONSEL group) that provided the as-cast magnesium alloy workpieces. The authors would like also to acknowledge the technical support of Dr.
BESSROUR, Jamel   +4 more
core   +1 more source

Influence of Al–5Ti–1B master alloy addition on the grain size of AZ91 alloy

open access: yesJournal of Magnesium and Alloys, 2017
The mechanical properties of castings depend on the grain size. There is evidence that titanium and boron (Al–5Ti–1B master alloy) affect the grain size of magnesium alloys. Here, the influence of the addition of 0–1 wt.
Andrey Koltygin   +2 more
doaj   +1 more source

Effect of constraint on tensile behavior of an AZ91 magnesium alloy [PDF]

open access: yes, 2004
The deformation and failure behaviour of a cast AZ91 alloy was investigated using tensile test on the circumferentially notched tensile\ud specimens with different notch radii.
Mai, Yiu-Wing, Yan, Cheng, Ye, Lin
core   +1 more source

The Effects of Rare Earth Pr and Heat Treatment on the Wear Properties of AZ91 Alloy

open access: yesCrystals, 2018
This paper investigated the influences of Pr addition and heat treatment (T6) on the dry sliding wear behavior of AZ91 alloy. The wear rates and friction coefficients were measured by using a pin-on-disc tribometer under loads of 30, 60 and 90 N at dry ...
Ning Li, Hong Yan
doaj   +1 more source

Home - About - Disclaimer - Privacy