Results 31 to 40 of about 20,056 (249)
The Journal of Indian Prosthodontic Society, 2019 Aim: The aim of this in vivo study was to evaluate and compare the retention and patient satisfaction in implant supported mandibular overdenture with three different attachment system. Materials and Methods: After evaluation of prosthetic space, fifteen
Nitish Varshney +3 more
doaj +1 more source
The Journal of Indian Prosthodontic Society, 2016 Aim: The aim of this in vitro study was to compare the change in the retentive force and removal torque of three attachment systems during simulation of insertion-removal cycles.
Tejomaya Shastry +3 more
doaj +1 more source
The Journal of Indian Prosthodontic Society, 2021 Aim: This systematic review aimed to compare different attachment systems used in mandibular implant supported overdentures by assessing outcomes such as prosthodontic maintenance and complication, peri implant tissue changes, retention, and patient ...
Priyanka Vaibhav Sutariya +5 more
doaj +1 more source
Characterizing the intermetallic formed during ball attach process [PDF]
Microscopy and Microanalysis, 2008 Continuously miniaturization of electronic components using PCB's technology for the manufacturing of SDRAM's uses a solder ball attach process, producing a joint which robustness and electrical response are crucial factors to success. At present, near-eutectic Sn-Ag-Cu alloys are the leading candidates for Pb-free solders.
Paulo Pereira +3 more
openaire +1 more source
Mandibular overdenture retained with precision balls and bar attachment
Stomatološki glasnik Srbije, 2022 Introduction Milled precision bar with the lateral additions of two precision attachments could significantly contribute to the primary and secondary retention of partial denture and overdenture. This clinical case demonstrates stability of mandibular overdenture using milled precision bar and two coronally positioned precision attachments. Case report
openaire +3 more sources
Journal of Advanced Pharmaceutical Technology & Research, 2022 This study aimed to compare strain around implants used as abutments for removable partial dentures with wrought wires and fixed partial dentures with ball attachments and fixed dentures with posterior cantilever.
Roodabeh Koodaryan +4 more
doaj +1 more source
Journal of Applied Biomaterials & Functional Materials, 2019 Introduction: The aim of this study was to evaluate the effect of different heights of attachment and mucosa thicknesses on the stress distribution of two implant-retained mandibular overdenture designs under loading using the photoelastic stress ...
Ozgun Yusuf Ozyilmaz +2 more
doaj +1 more source
Journal of Oral Research and Review, 2015 Conventional complete dentures primarily rely on residual alveolar ridge and mucosa for support and retention. Patients with poor mandibular ridge foundation usually suffer from inadequate denture retention and stability. In such cases, implant-supported
Jatin Agarwal, Rolly S Agarwal
doaj +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Medicina Oral Patología Oral y Cirugia Bucal, 2011 The purpose of this clinical study was to evaluate the complications associated with the different attachments used in implant-supported overdentures, including prosthetic problems and implant failures. A comparison of ball, bar and Locator (Zest Anchors, Inc, homepage, Escondido, CA, USA) attachments, in completely edentulous patients with two, three ...
Çakarer, Sirmahan +3 more
openaire +3 more sources