Results 191 to 200 of about 737,890 (266)

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

A novel lactam-based AIE building block for high-performance deep-blue electroluminescent materials. [PDF]

Chem Sci
Liu L, Lou J, Wan J, Li Y, Xiong H, Huang Y, Yang D, Zhang H, Tang BZ, Wang Z.   +9 more
europepmc   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Feasibility of neurite oriented diffusion and density imaging in thigh skeletal muscle of volunteers with knee pain: relationship with proton density fat fraction: a cross-sectional study. [PDF]

BMC Med Imaging
Wang Y, Qiu Z, Liu J, Chen Y, Zhang X, Liao R, Han D, Zhang X, Zhang X.   +8 more
europepmc   +1 more source

BASIC FORMULATION OF NUCLEAR LEVEL DENSITY CALCULATIONS

, 1971
Gilbert, A., Gatti, R.C., Struble, G.L.
openaire   +1 more source

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source

High-density lipoprotein-related inflammatory markers and their association with all-cause and cardiovascular mortality in an ageing population: findings from a prospective cohort study based on NHANES data. [PDF]

J Glob Health
Hu T, Chen R, Gu Y, Yu C, Liu X, Zhang X.   +5 more
europepmc   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

High-power laser powder bed fusion of pure copper for simultaneous achievement of high density and electrical conductivity. [PDF]

Sci Rep
Oh WJ, Son Y, Kim DH, Kim CS.
europepmc   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source