Results 71 to 80 of about 501,373 (309)
Bed-Load Rate on Movable Beds with Vegetation
PROCEEDINGS OF HYDRAULIC ENGINEERING, 1997 This paper is concerned with bed-load rate on movable beds ac companied by vegetation. Firstly, some flume experiments are carried out with two kinds of plant-models which are cylindrical and curved to downstream, and branched and inclined also to downstream.
Takeshi OKABE +2 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Water Resources ResearchExtreme precipitation is increasing the risk of dam breaks and formation occurring debris dams. Accurate prediction of dam‐break wave propagation is critical to disaster emergency management. Intense bed‐load transport by dam‐break floods can result in a
Xiafei Guan +4 more
doaj +1 more source
Bed load transport in braided gravel‐bed stream models
Earth Surface Processes and Landforms, 1988 AbstractBed load transport rate was measured in ten self‐formed small‐scale gravel braided streams developed in a laboratory flume at several different values of steady discharge and flume gradient. The streams are approximate Froude models of typical prototype braided streams but of no particular river.
openaire +3 more sources
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates innovative thermoreversible hydrogels derived from S53P4 bioactive glass extracts to aid in the healing of infected diabetic foot wounds. These injectable gels, which gel at body temperature, release beneficial ions and remain stable over time.
Marian G. Vargas Guerrero +9 more
wiley +1 more source
A comparative study of sequencing batch reactor and moving-bed sequencing batch reactor for piggery wastewater treatment [PDF]
Maejo International Journal of Science and Technology, 2011 This research aims to comparatively study the efficiency of piggery wastewater treatment by the moving-bed sequencing batch reactor (moving-bed SBR) system with held medium, and the conventional sequencing batch reactor (SBR) system, by varying the ...
Kwannate Sombatsompop
doaj
ABOUT FACTOR, CONDITIONNING PROCESS OF THE TRANSPORT CHANNELFORMING SEDIMENTS
Вестник Дагестанского государственного технического университета: Технические науки, 2016 In given article on base of the analysis of the literary sources and generalization experimental and натурных given are elaborated main factors, influencing upon process of the transport channel-forming sediments.
A. V. Magomedova, M. R. Magomedova
doaj +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source