Results 41 to 50 of about 159,089 (261)

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Prediction of bending properties for beech lumber using stress wave method

Maderas: Ciencia y Tecnología, 2014
In this study; bending properties of beech wood (Fagus orientalis) were predicted using stress – wave method and compared with static bending tests. First, lumbers which were different in length and cross section were weighed and dimensions were measured.
Ergun Guntekin, Serhat Ozkan, Tugba Yilmaz   +2 more
doaj  

Investigating the bending properties of cardiovascular catheters and stents via three-point bending test setup

Current Directions in Biomedical Engineering
The bending properties of catheters and stents have a big influence on their success during clinical application. Whereas bending stiffness directly affects the trackability of catheters, stents underlie bending when used for renal, superficial femoral ...
Brandt-Wunderlich Christoph, Lenz Christopher, Siewert Stefan, Stiehm Michael, Schmitz Klaus-Peter, Schmidt Wolfram   +5 more
doaj   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Moisture state and bending properties of Japanese larch (Larix kaempferi) boxed-heart timbers dried by high-temperature kiln-drying and stored under different conditions

Drewno
The high-temperature setting (HTS) method is a kiln-drying method in which boxed-heart (BH) timbers are rapidly dried at high temperatures and low relative humidity.
Yoshihiro Hosoo, Hirokazu Nishiwaki, Takashi Takeda, Takahisa Yoshida   +3 more
doaj   +1 more source

MEASURMENT OF BENDING PROPERTIES OF RHIZOPHORA TROPICAL WOOD

ASEAN Journal on Science and Technology for Development, 2017
The Young’s modulus, load at the yield point and proportional limit stress from the compression bending (cb) test were compared with the four point bending tests (4pb). The theoretical Young’s modulus are larger than the real reading for 5mm and 10mm thick specimens, except for 200mm long specimens due to specimen nonlinearity. The experimental results
Sinin Hamdan, Mahbub Hasan, Yoann Nohe
openaire   +3 more sources

Multimodal Data‐Driven Microstructure Characterization

Advanced Engineering Materials, EarlyView.
A self‐consistent autonomous workflow for EBSP‐based microstructure segmentation by integrating PCA, GMM clustering, and cNMF with information‐theoretic parameter selection, requiring no user input. An optimal ROI size related to characteristic grain size is identified.
Qi Zhang, Santiago Benito, Özge Özgün, Sebastian Weber, Markus Stricker   +4 more
wiley   +1 more source

Microstructure‐Controlled Crack Propagation and Fracture Resistance in MoSiBTiC Alloy Revealed by Multiscale Extended Finite Element Method Modeling

Advanced Engineering Materials, EarlyView.
A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du, Takahiro Kaneko, Xinyu Yan, Takahito Ohmura, Kyosuke Yoshimi   +4 more
wiley   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source