Results 101 to 110 of about 105,905 (259)

Tunable electrical and mechanical properties of anode foils for aluminum electrolytic capacitors prepared by additive manufacturing technology

Journal of Materials Research and Technology
An additive manufacturing technology was used to produce anode foils with different polystyrene microsphere (PSM). The effect of PSM addition in the range of 0–20 vol% on the specific capacitance and bending strength of the anode foils was investigated ...
Guangzhu Bai, Changrui Wang, Fang Wang, Yajun Ren, Xiaohong Xu   +4 more
doaj   +1 more source

Improvement in Bending Strength of Silicon Nitride through Laser Peening. [PDF]

Materials (Basel), 2022
Saigusa K, Yamamoto J, Takahashi K, Kumeno F, Shibuya N.   +4 more
europepmc   +1 more source

Bending strength design of gears

Tribology, 1969
AIDA, Toshio, ODA, Satoshi
openaire   +2 more sources

Wearable Kirigami‐Apertured Capacitive Sensors for Continuous Cardiac Volumetric Monitoring

Advanced Functional Materials, EarlyView.
A wearable kirigami‐apertured carbon nanotube‐paper composite (K‐CPC) capacitive sensor enables cardiac volumetric monitoring. The kirigami process creates a central aperture with cantilevered fibers that confine the electric field, enhancing both sensitivity and lateral resolution.
Yu‐Jen Cheng, Shawn Kim, Jonathan Avery, Younghoon Kwon, Jae‐Hyun Chung   +4 more
wiley   +1 more source

Statistical Modelling of the Fatigue Bending Strength of Norway Spruce Wood. [PDF]

Materials (Basel), 2022
Klemenc J, Fajdiga G.
europepmc   +1 more source

Design and Characterization of a Two‐Dimensional Soft Array Based on Cooperative Dielectric Elastomer Actuators

Advanced Functional Materials, EarlyView.
A fully polymeric two‐dimensional array of Dielectric Elastomers enables self‐sensing, cooperative actuation, and large‐stroke operation in a DE‐based autonomous conveyor. Based only on voltage and current measurements at actuator level, the system detects the presence of a ball and subsequently drives it toward a target position.
Saverio Addario, Alberto Priuli, Giovanni Soleti, Sebastian Gratz‐Kelly, Benjamin Zemlin, Stefan Seelecke, Gianluca Rizzello   +6 more
wiley   +1 more source

Bending Strength of Polyamide-Based Composites Obtained during the Fused Filament Fabrication (FFF) Process. [PDF]

Materials (Basel), 2022
Mazurkiewicz M, Kluczyński J, Jasik K, Sarzyński B, Szachogłuchowicz I, Łuszczek J, Torzewski J, Śnieżek L, Grzelak K, Małek M.   +9 more
europepmc   +1 more source

Coordinated Architectural and Chemical Reinforcement in the Crushing Mandible of a Soldier Termite

Advanced Functional Materials, EarlyView.
The crushing mandible of a soldier termite withstands substantial biting loads despite lacking mineral. Its cuticle is partitioned: convex teeth pair hardness and zinc enrichment with aligned chitin fibers for contact durability, while stiffer concave regions between teeth carry bending loads.
Andrew Tran Nguyen, Patryk Wąsik, Juan Fernando Cucuyame Morales, Marie Kate Palau, Adrian Francisco Duran Ornelas, Phani Saketh Dasika, Jin Hee Kim, Radhika Laxminarayana, Eric Hintsala, Greta Chang, Junzhi Liao, Lizhi Sun, Nathan Lord, Atsushi Arakaki, Paul Bardunias, Pablo Zavattieri, David Kisailus   +16 more
wiley   +1 more source

Determination of Gear Bending Fatigue Limit based on Up and Down Method

Jixie chuandong, 2015
The bending fatigue strength of gear is an important indicator for gear performance,and it is an effective method to obtain the bending strength according to the test procedure.
Yang Guangming
doaj  

Bending Strength of Wood Treated with Propolis Extract and Silicon Compounds. [PDF]

Materials (Basel), 2021
Woźniak M, Mania P, Roszyk E, Ratajczak I.   +3 more
europepmc   +1 more source