Results 251 to 260 of about 474,134 (309)
Research on Friction Welded Connections of B500SP Reinforcement Bars with 1.4301 (AISI 304) and 1.4021 (AISI 420) Stainless Steel Bars. [PDF]
Materials (Basel)Michałek J, Krawczyk R.
europepmc +1 more source
Some of the next articles are maybe not open access.
Related searches:
Related searches:
Electrical Transmission in a New Age, 2002
The paper presents the results of tests on six single angles under minor axis bending, thirteen double angles under geometric axis bending, and eight laterally unsupported single angle beams with long legs horizontal. All twenty-seven specimens developed full plastic moment.
Murty K. S. Madugula, Yongcong Ding
openaire +1 more source
The paper presents the results of tests on six single angles under minor axis bending, thirteen double angles under geometric axis bending, and eight laterally unsupported single angle beams with long legs horizontal. All twenty-seven specimens developed full plastic moment.
Murty K. S. Madugula, Yongcong Ding
openaire +1 more source
Bending strength of porcelains
Ceramics International, 2002Abstract Porcelains in the quartz–metahalloysite+kaolin–K-feldspar system with different quartz grain sizes were investigated to study the effect of firing temperature on the bending strength. The degree of vitrification of the fired bodies was determined measuring the bulk density, relative percentages of constituent minerals by XRD and their ...
O.Isik Ece, Zenbe-e Nakagawa
openaire +1 more source
Ultimate Bending Strength of Si Nanowires
Nano Letters, 2012Test platforms for the ideal strength of materials are provided by almost defect-free nanostructures (nanowires, nanotubes, nanoparticles, for example). In this work, the ultimate bending strengths of Si nanowires with radii in the 20-60 nm range were investigated by using a new bending protocol.
G, Stan +4 more
openaire +2 more sources
Bending strength of spruce glulam
European Journal of Wood and Wood Products, 2009A glulam strength model where the bending strength depends both on the board tensile strength and the finger joint tensile strength is a completely transparent model being particularly suitable to determine requirements for the board and for the finger joint tensile strength of glulam made of both visually or mechanically strength graded boards.
Frese, Matthias, Blaß, Hans Joachim
openaire +1 more source
Bending strength of silica glass
Journal of Materials Science, 2000Tensile and bending tests are useful to characterize the mechanical behavior of ceramics. Theoretical comparisons between results of both tests are usually done based on Weibull statistics. In previous experiments on borosilicate glass, no agreement was found between experimental and theoretical values of the ratio of the maximum bending and tensile ...
R. E. Medrano, P. P. Gillis
openaire +1 more source
Tibia Bending: Strength and Response
SAE Technical Paper Series, 1985<div class="htmlview paragraph">Unembalmed human tibias were subjected to static and dynamic three-point bending tests using the Wayne State Translational Impactor. Simple supports potted to the bone near the proximal and distal epiphyses were attached to force transducers and load was applied at midspan by a 32-kg impactor that had a rigid 25-mm
Gerald W. Nyquist +3 more
openaire +1 more source
Journal of Structural Engineering, 1990
This is the description of a model that explains the relationship between the three strength properties, tension, compression and bending. The model which included nonlinear compresion behavior and size dependent brittle tension behavior of wood, has been calibrated and verified with reference to test results.
openaire +1 more source
This is the description of a model that explains the relationship between the three strength properties, tension, compression and bending. The model which included nonlinear compresion behavior and size dependent brittle tension behavior of wood, has been calibrated and verified with reference to test results.
openaire +1 more source