Results 31 to 40 of about 96,110 (264)
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Nihon Kikai Gakkai ronbunshu, 2015 An inverse analysis method was proposed for estimating nonlinear stress-strain curve with plastic deformation from load-deflection curve of three-point bending test of simply supported beam with rectangular cross section. This method was based on a small
Yuko SAWADA, Shiro KUBO
doaj +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Jixie chuandong, 2013 According to the analysis of the limitations of traditional method of tooth root bending stress calculation using in fatigue lifetime prediction, a method of calculating tooth root bending stress of involute spur gear under random loading is developed ...
王建平 +5 more
doaj
Bending stress modeling of dismountable furniture joints applied with a use of finite element method
Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 2009 Presented work focuses on bending moment stress modeling of dismountable furniture joints with a use of Finite Element Method. The joints are created from Minifix and Rondorfix cams combined with non-glued wooden dowels.
Milan Šimek, Petr Koňas
doaj +1 more source
Physico-Mechanical Properties of Sugarcane Stalks
Acta Technologica Agriculturae, 2023 Manual harvesting of sugarcane requires skilled labourers, as improper harvesting leads to a significant loss of yield. Therefore, it is necessary to move towards designing a system capable of harvesting sugarcane on smallholdings, with high harvesting ...
Abdelhady Ahmed +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley +1 more source
Biomechanics of buttressed trees: bending strains and stresses [PDF]
American Journal of Botany, 2003 The different hypotheses about buttress function and formation mainly involve mechanical theory. Forces were applied to two trees of Sloanea spp., a tropical genus that develops typical thin buttresses, and the three‐dimensional strains were measured at different parts of the trunk base.
Clair, Bruno +4 more
openaire +5 more sources
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source